Jump to content
SAU Community

Katech GloCruise - 16/10/04

Omurru

By Omurru,
in Archived Events

 Share

Recommended Posts

Omurru Veteran

Omurru

Posted
Posted

Cruise will be starting at 7pm on the top level of the Glen Carpark in Glen Waverley and going up round the Dandenongs to Kinglake then back to the Maccas on the Hume Hwy in Campbellfield.

Everybody is invited to join in. As the name GloCruise suggests the theme of the

cruise is "rice lights" so come show us what you`ve got.

http://www.katech.com.au/glowcruise.pdf

Link to comment
https://www.sau.com.au/forums/topic/53445-katech-glocruise-161004/
Share on other sites
Downforce Grand Master

Downforce

Posted
Posted
dont forget we have the Official OPEN cruise that same day during the day.

And this cruise is going through very similar areas that we too will be travelling not a few hours before.

cheers - ash

Yeah I know, unfortunately I cant make it during the day..

..and damn u for closing the other thread about the Melbourne September 27 (2002) night cruise, I had just typed out a good reply to the guy who bumped it up wanting the details for a cruise that's already been and gone over 2 years ago :P Get off the net Ash u bum thefinger.gif

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Well, this is probably where a wiring diagram and a multimeter come into play.
    • Jarsky
      gauge needle removal

      By Jarsky · Posted

      I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Jarsky
      R33 GTST Axles

      By Jarsky · Posted

      Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Jarsky
      R34 Speedo not working after manual swap

      By Jarsky · Posted

      Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...