Jump to content
SAU Community

GTR Adapter 65=>80mm

Penfold

By Penfold,
in Engines & Forced Induction

 Share

Recommended Posts

Penfold Rising Star

Penfold

Posted
Posted

I have an old HKS aluminium induction kit on my R33 GTR but now I want to hook up Z32 AFM's. Unfortunately the AFMs are like 80mm & the GTR ones are 65mm which means my existing HKS piping won't hook up (connected the standard 65mm AFMs via the short HKS 65mm=>80mm intake piping). I have a cold air partition made up so it all fits nicely so I was wondering if you guys had heard of an adapter or something which would do the trick.

Heres a pic of my setup before its under the CAI (which is cool but I could just bolt on filters as i need some equivalent piping to reach.

http://home.austarnet.com.au/myra/gtr_filters.jpg

http://home.austarnet.com.au/myra/filtersmall.jpg

I have seen these that I'd have to weld up to some 80mm piping but was wondering if HKS make a similar product or sell just the replacement piping? http://www.starperformanceautoparts.com.au...daptors/a5.JPGC

Also, whats the deal with this:

http://www.hksusa.com/products/?id=639

Would the Nissan Maxima ones be the right ones because the 300ZX ones look nothing like it & they are 100mm they reckon??

If i had the right code number I think i could order through Nengun with other stuff.

Or if doughboy has something lying around from a GTR that would do they same job :mad:

Cheers,

Penfold

Link to comment
https://www.sau.com.au/forums/topic/54812-gtr-adapter-6580mm/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • joshuaho96
      R34 25GT Engine Light 21

      By joshuaho96 · Posted

      Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • GTSBoy
      R32 GTS (RB20DE) Injectors Replacement

      By GTSBoy · Posted

      No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • codygrimm27
      Can you mount the ATTESA pump in other locations?

      By codygrimm27 · Posted

      Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...