Jump to content
SAU Community

Recommended Posts

Howdy fellow Stagea owners :P

A strange thing happend this morning when I started the car up.

Did the usual and let it warm up a bit before driving off but as soon as I pressed the brake lightly the revs increased from 1100 (cold) to 1500. Take the foot off the brake and the revs dropped back down to 1100 again.

Got to work and the car was warm. Normal idle is about 700rpm, lightly press the brake and the revs increased to ~1100rpm. And putting around the car park slowly in D I could feel the revs increase as I pressed the brake, so it does it in D and N/Park (it's an auto !!).

Strange... The first thing I thought of was an air leak in the brake booster or vacum hose going to it - but being at work I haven't had a chance to pop the bonnet.

Any ideas ?

J

that sounds weird but i have heard of this before my wifes ford fairmont used to the do the same thing couldnt for the life of me figure out what it was but once i flushed the brakes and fitted new pads all round and put new front discs on it went away. I would be very interested to find out what the problem is.

Hi J, common problem, you just lead a sheltered life. Has the brake pedal effort increased noticeably since it started this? If it has, then it's a hole in the brake master cylinder diaphram, ouch not cheap. If the pedal effort hasn't increased (even slightly) then it's the one way valve in the line from the plenum to the master cylinder, it stops boost getting past. If the pedal effort has increased a lttle bit (maybe hardly noticeable) then it's the hoses/clamps, either the clamp/s will be loose or one of the hoses has a split in it.

Hope that helps, please let me know what it ends up being:cheers:

Thanks for the replies guys.

This is the first auto I've owned, so I'm a bit nude when it comes to this wierd transmission stuff :D

OK, drove it home this afternoon (had the arvo off :P ) and it's stopped doing it which is good.

Another good thing is that the pedal feel/hardness hasn't changed a bit. Not even the slightest.

So I'm hoping that it's the valve in the vacume line to the brake booster or just a loose clamp. I took the AAC valve off over the weekend and cleaned all the crap out of it, and while I was doing it I was leaning and hanging off a few hoses, so maybe I've loosened one a little or pulled on it a tad to hard and cracked it :)

I'll give it all a good look over and post up how I go.

One other thing that I've noticed (and is the reason why I cleaned the ACC valve), is sometimes going from D to park (or even netural) the revs will hunt a little for a few seconds.

It sort of drops low then comes up and drops a little then then settles at normal. It's not as bad (or frequent) now that I've cleaned the crap out of the ACC valve, but still does it a little. Oh, and it has never done it when the air conditioner is on.

J

Mine idles beautifully and the revs increase by less than 100 rpm for an instant when the brake is depressed and then it quickly returns to its nice stable 700 rpm.:D

Mine idles fine, and i just clocked over onto 110,000km.

My R33 used to idle weirdly, and i narrowed it down to faulty AAC valve or TPS swtich. same engine so maybe similar problems?

Cool, yeah the funny idle only happens when you move the shifter from D to Park. Doesn't do it when moving from Park to D or when the air con is on. Appart from the funny problem yesterday, pressing the brake has no effect on the idle.

The 'idle increasing when the brake is pressed' hasn't happend since yesterday, so I think the valve just needs a clean.

I'll rip it out on the weekend and give it a hit of WD40 and brake cleaner :)

J

The idle on my RS4 occasionally drops to around 600 instead of the usual 700 (which makes it stumble when accelerating from a standstill). It has also been known to hunt between 700-800 when in N (like the AAC is oscillating). I think a clean-up might be in order....

It is perfectly normal for the rpm to flare slightly when depressing the brake - but no more than a few hundred rpm max. If you pump the brakes repeatedly you should be able to get the engine to hover around 1000rpm. It will then settle back down when you stop (handy for old cars that have dodgy chokes!).

  • 3 weeks later...

have you checked for leaks in and around the brake booster?

if the pedal feels normal, but pumping it increases engine revs it normally indicates a vacuum leak in the power assistance. It shouldn't affect your brakeing capacity, but might interfere with ABS and will rev the engine etc..

it could be something else, but from all the cars i've seen with a similar problem, it's normally a vacuum leak somewhere

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
    • Trailer prep is underway... Lined up the wheel to get a rough indication of how it would sit Then removed all the bits (as far as possible) and gave the frame a light sand and quick lick of paint   Then added some carpet
    • okay, so I figured this out, removed needles and reinstalled after swapping the gauge face on my triple gauge for my ER34, all work and look good. I tried to do the same for the main cluster, but the main cluster gauge faces are dished, the replacement gauge face are flat, so due to the dish in the org face ,mounting backing plate (clear) and depth of the needle, the flat gauge face will not work. I notice that R34 gtr gauges are flat, appears to be different clear backing plate that aren't dished. are these available, or what have others done to install flat gauge faces?
×
×
  • Create New...