Jump to content
SAU Community

Quality USED GTR parts Nismo Trust Apex HKS

calvintys
 Share

Recommended Posts

calvintys Experienced

calvintys

Posted
Posted

I have the following below parts for sale.

1.One set of USED Trust H-Bean Con rod with 21mm pin for RB26 with standard crank (complete with Trust bolt or anything when you buy new from Trust). Perfect working condition, will provide full refund if find any error on the rod or anything that it does not give you satisfaction. = $1800

2.One set Trust Piston with ring with 21mm pin and diameter is 87.5 pie (2657cc). (Complete with Trust bolt or anything when you buy new from Trust). Perfect working condition, will provide full refund if find any error on the piston or anything that it does not give you satisfaction. = $1400

3. SOLD

4.Complete set of USED HKS EVC 5 boost controller, perfect working condition = $700.

5.USED Apexi Power FC with Hand controller r32/33 gtr (In BOX) = $1000.

6.SOLD

7.SOLD

8.Stock GTR Intercooler with sign of being repair due to some crack issue on Fin. However there is not leak or anything now. It is in a good working condition and will also provide full refund if it leak. $360.

Contact [email protected] or 0418 388 125. Melbourne CBD.

Cheers

Calvin

GTRgeoff Grand Master

GTRgeoff

Posted
Posted
6.Used 6 nismo 600cc injector with standard GTR fuel rail and resistor pack = $700 (The fuel rail and resistor pack is for those whom wanted to install it on RB25DET.)

Are you still interested in selling these? Call me on 0408 124 767

calvintys Experienced

calvintys

Posted
  • Author
Posted
how old is the piston kit? so it comes with everything i need? can i get your phone number? thanks

The piston has done less the 3000 KM. If you look at the piston head it still look very new as in No mark or nothing but there is some fine mark on the piston wall. Yes it came with everything you need. All genuine trust parts. My contact number is 0418 388 125.

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...