Jump to content
SAU Community

Recommended Posts

Help with steering!!!

Hi,

I have just done wheel balance on my car on all 4 tyres.

This has been done twice now at two different TyrePower shops.

Resolution after $120 spent: The steering still shakes as soon as I hit 100km/h.

I thought it was my tyres, I don’t know. I don’t remember hitting anything at all.

So I don’t think it would be my mags. Possibly one of the tyres is defective, Front.

Thinking if it is backs, the whole car would shake. So it must be fronts. Either front rubber is defective or the mags are buckled. The guys at TyrePower reckons that’s not the case. I don’t know what else could be the problem. Can you guys offer some sort of assistance even if it is a wheel specialist place.

Thanks heaps.

Al

Link to comment
https://www.sau.com.au/forums/topic/55820-help-with-steering/
Share on other sites

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

have a similar problem have a theory that its the front bushes that have started to show cracks probably cracked on insides first and worked way out thats why we couln figure it out my mechanic thinks i might be right am getting whole new suspension soon ( whiteline works kit) this better fix it

have a similar problem have a theory that its the front bushes that have started to show cracks probably cracked on insides first and worked way out thats why we couln figure it out my mechanic thinks i might be right am getting whole new suspension soon ( whiteline works kit) this better fix it

I was told by a mechanic that the suspension wouldn't affect just a steering, but the whole car. So I am inclined to say wheels. It's only the steering that shakes at early100. Even thought it was my discs. But that would only affect breaking. So the steering would pull to the dirrection of the front disc that is not grinded as much.

That's what I was told. I m getting the all machined and new brakes done aswell.

Some sort of Bendix. Any advice on Bendix while we are on the subject.

Bendix Advance front and rear plus all for machined disc's for $340.

I think that sounds ok. What do you think?

Al

ah yes true but mines only a theory and i need new suspension anywho i find i have a vibration between 85ish - 115ish no probs on strip or track vibration on acceleration deceleration and at steady pace mechanic sed the bushes that are cracked cop the full weight of the front of the vehicle and so may cause it but that theres no danger of s%$t hitting fan sort of thing

Help with steering!!!

Hi,

I have just done wheel balance on my car on all 4 tyres.

This has been done twice now at two different TyrePower shops.

Resolution after $120 spent: The steering still shakes as soon as I hit 100km/h.

I thought it was my tyres, I don’t know. I don’t remember hitting anything at all.

So I don’t think it would be my mags. Possibly one of the tyres is defective, Front.  

Thinking if it is backs, the whole car would shake. So it must be fronts. Either front rubber is defective or the mags are buckled. The guys at TyrePower reckons that’s not the case. I don’t know what else could be the problem. Can you guys offer some sort of assistance even if it is a wheel specialist place.

Thanks heaps.

Al

How's the wheel alignment?

How's the wheel alignment?

Alignment is fine ,

In that case it would only make the car push left or the opposite on the straight...

Depending on speed. I don't think the alignment would have anything to do with vibrations on steering at particular sped.

If I am wrong please guys explain how that is possible. As the vibrations are on 100 sharp and constant after that. Alignment would affect it on lover speed...

Yes?

If the alignment is out it can only show itself at certain speed ranges, As i have experienced in my Magna. I have a similar problem that at 70 - 90 kms i could feel a shudder but soon as i got over say 95kms it was smooth again. Saying that soon as i got under 70kms it was fine too it was only that range of 70 - 90kms.

So i got a wheel alignment done and it was fixed, i defiantly dont know much about cars or evan physics to explain it. Our problems sounded familiar so i though i would share, i hope i have helped.

Alignment is fine ,  

In that case it would only make the car push left or the opposite on the straight...

Depending on speed. I don't think the alignment would have anything to do with vibrations on steering at particular sped.

If I am wrong please guys explain how that is possible. As the vibrations are on 100 sharp and constant after that. Alignment would affect it on lover speed...

Yes?

when I first got my "line", it would shudder when I reached around 115-120km/hr. The wheels were balanced, yet still that shudder. Didn't do much about it after that as I didn't often go that speed anyway.

When I discovered that the insides of the front tyres were wearing bad (excessive negative camber) I got the alignment checked and camber kit had to be installed as camber was way too much on the negative side. Negative camber will not necessarily give shudder as race cars use huge amounts of -tive camber, depending on track layout. Anyway the shudder is no longer there so I suspect something else in the alignment was out.

Pulling left or right doesn't necessarily have to be a symptom for the alignment to be out.

A failure in a tyre wall could be a possibility for shuddering or other tyre problems.

If you are able, try to swap your front wheels and tyres with one of your mates and take it for a spin. That way you will be able to discount the tyre factor.

If that checks out ok, then you might look at suspension bushes or even shockies.

Hope that helps

when my car got here from japan it had a bad vibration and the compliance workshop got all 4 wheels balanced and aligned however the problem still persisted. He dropped the tailshaft and he 3 uni-joints were worn and not moving freely he sent it off to some place in osborne park and they machined the joints and replaced them and all was fine again.

I had this problem a while ago...

Had 235 rears and 215 fronts, and i always had a vibration at about 110-120ish, went thru like 2 different sets of tyres and it was still there...

... then I got 255 rears, and 235 fronts..... were told the rims were slightly buckled while my tyre guy was doing the balancing, but put them on the car and it was perfect!

It might be your choice of rubber - but if you got two completely different brands both times it wouldn't be that?

i have same thing when i hit 120km :Paranoid:

Steering wheel wobbles after alignments, new rubber, new pads and new bushes ...... give up ..... i just cling to the steering wheel harder :P

hahaha so im not the onli one having problems :D my whole car is fkd, the people that did the custom boss kit thingy for steering wheel did it for it to be straight and now its gone wonky and stays wonky... its like tilted when u drive straight... with the car pushing to left when u drive straight, and it sometimes does that shaking shit that u guys are talkin about when goin through different speeds...

Guys I was told by all the tyre places and the mechanics that the suspension would not affect the steering, entire car would be affected. Not just an isolated steering problem. Most likely its the tyres. I have Goodyear, Venturas. $150each, brand new. Found out they have bumps in the circle fronface. When the wheel is rotating you can see the bumps on it. Even with the alignment done to 0.5g an all sides. I think I have crap tyres. It's gona be a Bad year with my GoodYEars. Hope I find something other than that solution.

And guys my steering is critical, it shakes 1 to 2 cm on both sides. at 100-120...not drivable.

Hope someone can recomend a good place.

Al

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I thought Australia got rid of the "drag dodgy fuel up to 91 RON with ethanol", which is why all E10 advertise as "up to 94 RON" ? Anyway I put E10/91 in the missus' Mazda because she empties the tank weekly, when all my cars get 98RON. tl;dr - turbo - 98 RON, if you can't afford that, sell it and get a commuter car (or tune your car for 91, which no one does).
    • Yeah i found that alot of parts can be wrong or "very" hard to get the real right one. I already bought some brakes years ago on me "old" GT calipers and they were wrong too 😄  I told them too. Even send them pictures...but they said "EBC catalogue has them on my car... So i dont know what their answer will be. I call monday them and let them know that they are really not on my car. If they were they would be already on a car...
    • Welcome to Skyline ownership. Yes, it is entirely possible parts websites get things wrong. There's a whole world of inaccuracies out there when it comes to R34 stuff (and probably 33 and 32). Lots of things that are 'just bolt on, entirely interchangable' aren't. Even between S1 and S2 R34's. Yes they have a GTT item supposedly being 296mm. This is incorrect. I would call whoever you got them from and return them and let them know the GTT actually uses 310mm rotors. Depending on where you got them from your experience and success will obviously vary.
    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
×
×
  • Create New...