Jump to content
SAU Community

Recommended Posts

This is a follow up to my previous call for help.

Since installing my profec B, I continue to come on to boost much later than I did with a bleed valve.

Has anyone in SA got a Profec B (series 1) boost controller? (private or business)

If I could catch up with you and swap their controller (black unit under the bonnet with 2 vacume lines attached) with mine for 5 minutes and take the car for a spin around the block it would be much appreciated, and help me determine if the fault lies with my unit or the turbo. - (10-15 minute job from start to finish)

I'm getting desperate guys, the car drives well but it takes so long to come on to boost that its not funny. (no feeling of power until 4500-5000 rpm.

Link to comment
https://www.sau.com.au/forums/topic/55861-help-with-profec-b-boost-controller/
Share on other sites

Hi Maxx

I have checked for leaks, but havnt found any. It holds its pressure/vacume well, and I have it set to 13psi (no trouble and no spikes).

But wouldnt a leak give me higher boost?

After all a bleed valve is really just a controlled leak device, so is anything a leak should give me more boost (not that the amount of boost is a problem)

My problem is that the boost is comming on much later in the rev range.

Thanks for your thoughts however.

If anyone else has had this problem I am open to your ideas as well.

hey Steve, I had the same problem .... I bought my ProfecB from an Australian guy in Japan called Japandy. Tilbrooks installed it and it did the same thing as yours - would not limit boost it just kept climbing. So I got Japandy to send me another solenoid and it did exactly the same thing. So I got him to send me another head unit and it did EXACTLY the same damn thing!!!! Mark from Tilbrooks had a heap of different people have a look at it, but they all said it was hooked up right. So they sent the 2 head units and 1 solenoid to James at D1 and he said they both worked perfect on the bench, holding and releasing pressure. I gave up, and bought a new Hybrid EBC.

George from GT Autosound was installing my Hybrid, and he said he couldn't get it to work - it would just skyrocket the boost!!! SAME DAMN THING!!! He said, he switched a couple of the wires around, and it works perfect. He said the wiring was mixed up from the factory (wrong colour wires) - and the ProfecB would have worked fine if the wires had been switched around. Not sure if this story helps, but maybe you have the same problem?

Weq

The sharp/soft dial you are talking about is set to 100% sharp - things only get worse if i turn it towards soft.

Thanks for the thought though.

If anyone else has had this problem I am open to your ideas as well.

Problem sorted, the boost controller works well and is really easy to set up.

4 Door, have you checked the switch settings on the back of the controller, as greddy show a setting to use if 'overboosting' - perhaps this is how yours is set, which would explain why it takes longer to come on boost.

good in theory anyways:)

Thanks for the loan of the solenoid and controller, :thankyou: I have tried both and the problem still remains. ;)

I have also replaced all of the vacuum hoses, and have now plumbed the control unit into the bow-off vacuum line (to further reduce the length of hose) but the problem still remains. :rofl:

At this stage I will accept help from Japanese Holly men :ghost: , Voodoo priests, Jedi knights ;) or anyone else with similar qualifications

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...