Jump to content
SAU Community

Recommended Posts

ok im installing a boost gauge but dnt wana **** it up. Im to connect it to the hose running off the intake manifold but im not sure where that is on my r33 gtst. I think its what my boost controller is connected to but wana make sure. Can any1 help, any1 got pics of the intake manifold and where i should be connecting the gauge to.

Link to comment
https://www.sau.com.au/forums/topic/56226-wheres-my-intake-manifold/
Share on other sites

I did mine last weekend. I used the hose where the fuel rail ends and goes back to the pleneum, but my brother said if it stuffs up, it could fry your engine.

so i moved it to where the pipe that goes to the BOV and tee it of there. You can basically use any hose that has vacum/pressure.

Didnt have a camera to take pics. can do it this weekend.

can any1 tell me the best position??

missionary

- the ole fashion way of doing it. seems to work fine.

on your knees

- common practice in churches

see how u got that pipe running over the top of your engine ..and it goes into that big bendy shape thing.. thats your intake and intake manifold ...on the back towards your firewall ..u should have a fitting on the back for your standard boost gauge....now depending on what boost gauge u have ..u should b able to tee into that .. or remove the standard fitting and fit the new on in thesame hole.

yes?

Matt

missionary

-  the ole fashion way of doing it. seems to work fine.  

on your knees  

- common practice in churches

see how u got that pipe running over the top of your engine ..and it goes into that big bendy shape thing.. thats your intake and intake manifold ...on the back towards your firewall ..u should have a fitting on the back for your standard boost gauge....now depending on what boost gauge u have ..u should b able to tee into that .. or remove the standard fitting and fit the new on in thesame hole.

yes?

Matt

ok lookin at the engine from the front it should be in left back corner next to firewall, right? im jst confused coz sum1 told me to connect it the hose connected to the boost controller.

The only hole to get thru the firewall is on the right hand side when lookin at the engine from the front so i have to run it around ay.

seriously man its not that hard.

find a vaccum/boost line, T-piece into it and you're done.

again if you dont even know what an inlet manifold is or how to Tee in a boost line then you shouldnt be working on your car! Asking questions on a text based forum isnt going to help much either.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...