Jump to content
SAU Community

Recommended Posts

CHEAP!!!! R32 GTR '89 - 56,000km - $21,500

Got a DEAD stock R32 GTR for sale

*DEC 1989 build (one of very few in australia, for the time being)

*56,000km on the clock (cant prove its right, but it looks like the car has very low km)

*Gunmetal grey

*Had engine rebuild in japan 11,000 km ago (why i dont know but it has!)

*Just freshened up the breaks (machine, and bendix ultamate pads all round)

*Just rebuilt clutch master cylinder and booster

*Just changed all fluids and filters top to bottom

*Rego for 10 months

*Everything works (excpt no a/c gas as it was degassed in japan, but ac does work)

*NO MODS!!!!!!

*Top of the range alarm with 3 point immobilizer just installed (works GREAT!)

Pics at http://chubby.nameserve.org/~mypics/gtr/

only probs with the car are:

*slight exhaust leak, Pretty sure its the gasket from the cat to the rear section of the exhaust

*wear on the drivers seat (very common)

*dint on left front guard can see in the 2nd pic, but only notice it if your looking for it.

Very nice clean car

$21,500

Sydney 0410496449 Jacob

Reason for sale, lost my licence can show paper work

Link to comment
https://www.sau.com.au/forums/topic/56788-cheap-r32-gtr-89-56000km-22500/
Share on other sites

i dont like to make people read "bump" for half a page.

For anyone who is interested in reading the other thread the address is http://www.skylinesaustralia.com/forums/sh...ead.php?t=53907

Some questions and lots of "bumps"

Hey,

Is it privately imported or you are the second owner in Oz?

Might be interested but not for couple of months...

Cheers

Grant

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...