Jump to content
SAU Community

Left Side.....got Nothing!!!!!! Plz Help!!!!!!


Recommended Posts

hi guys, i have a R33 gtst with front kenwood speakers and rear clarion speakers and a kenwood head unit (all came with car from japan / head unit only works in japanese channels) anyway im not concerned about the radio stations, i just wana play cds and it was all working good until about a week ago when the whole left side of the speaker stopped working and the window on the passsenger side has been slow since i bought it, but now it has stopped too and wont wind up or go down (just stuck), now i havent touched a thing since ive had it just pulled it apart to clean contacts and check wires behind head unit,(looks professional install) still nothing. im at a loss??? is there anywiring relays or anything that could be stopping the stereo and window from working?? im not good with stereos, i usually get my mate to sort it out and even he didnt know. H.E.L.P M.E PLZ!!!!!!!

Link to comment
https://www.sau.com.au/forums/topic/57024-left-sidegot-nothing-plz-help/
Share on other sites

Do you own or can you borrow a multimeter?

Those systems to my knowledge are unrelated, so start probing the contacts in the doors and work your way back to find the fault.

Perhaps there is wiring harness damage in the cabin to door grommet.

yea sounds like you have got some damage to the wiring going to the left door. im not to sure on the skylines but do they have the black tubbing which your wires run through? if so try and get around that and check that no wire have broken off inside. sounds like the whole lot is damaged or something is cross wired.

dave

p.s if u have any more problems send me a pm and i will help u out

sorry i didnt reply guys i been busy, i found out what the problem was! my mate does electronics and he pulled apart the head unit after we tried everything else and he said all the soldering of the wires were dodgy, must have been a stuff up[ in the factory! so it came with the car like that, and all the left channels werent working and he said the right ines were just about gone aswell. any1 ever had this problem or heard of it. i certainly never have! crazy stuff! and where is kenwood made anyhow??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
×
×
  • Create New...