Jump to content
SAU Community

Recommended Posts

so i got the standard r32GTS-t. What do I need to do to get higher boost pressure and what is involved if you know what I mean. I am a newbie never done this before. What do I need ie. Boost controller bla bla bla and will my ecu need and re-mappin and all that necesary info please.

Thank you all looking for some more power to join the next level ( i wish )

Link to comment
https://www.sau.com.au/forums/topic/57105-upping-the-boost/
Share on other sites

from what youve said its alot more involved than you think.

before running higher boost, you'll want either a full cat back or turbo back exhaust, your current exhaust wont be able to get enough air through it once boost is turned up, so you wont gain much power as the engine will be hurting itself as it struggles to force the air back out the exhaust, kinda like tyring to push an orange through a drinking straw.

i'd also suggest getting a pod filter, once the boost is turned up the turbo will be sucking in a hell of a lot more air, having a pod filter will suck in more air and do it more efficiently and faster, thus feeding the turbo the extra air it needs.

in regard to the boost controller you will need, i'd suggest staying away from bleed valves (they are a valve that fools the turbo into thinking its getting less air so it spools harder to compensate, which turns into more power, correct me if im wrong guys but this is the basic premise right?)

i would go with an electronic boost controller (something like an apexi or hks) as it wont spike and its much easier to control what boost you run and easier to adjust.

also it would be a good idea to install a front mount intercooler (FMIC) as the days are getting much hotter, if you run higher boost the car will get much hotter and likely doing damage due to overheating. the FMIC will cool the engine and keep your running temp nice and low. and it will also give you more power.

your current ecu will have a boost cut installed but shouldnt come into play unless you run very high boost, dont run your boost cont over 12psi, as the stock turbo, clutch and internals will most likely sh*t themselves eventually.

so thats a brief run down for you on what you'll need to get started. im sure i have some details wrong so guys please feel to correct me. hope that helps

Andrew.

Link to comment
https://www.sau.com.au/forums/topic/57105-upping-the-boost/#findComment-1103782
Share on other sites

epends on where you are. in most places your only allowed to have one different means of induction (i think thats the term) so either a pod filter or FMIC.

in canberra however you can have whatever you want. but if you start modifying your car to be completely legal you can forget it immediatly, its basically a matter of hiding what you have or accepting that your gonna cop defects.

Link to comment
https://www.sau.com.au/forums/topic/57105-upping-the-boost/#findComment-1104159
Share on other sites

easy way out of it is just buy a turbosmart bleed valve and simply up the boost to around 10psi. Better way is to get an exhaust, intercooler then boost it up around 12psi and tune up with an air/fuel controller or computer. Depends how far you want to go, and how much $$$ you want to spend...

Link to comment
https://www.sau.com.au/forums/topic/57105-upping-the-boost/#findComment-1104198
Share on other sites

You could look into using bits off the R32 GTR ie filter and intercooler , with the appropriate fixings they are a factoty fit and look . The only mod required is the plumbing from the throttle body to meet up with the GTR intercooler outlet .

Generally the easiest if not cheapest upgrade bits come from the highest performance model of the type ie R32 and GTR . The parts are all factory engineered to suit the type . Most things off the GTR can fit into the GTST but the floor pans are slightly different so forget about the AWD transmission . If you wanted this buy a GTS4 or GTR .

Link to comment
https://www.sau.com.au/forums/topic/57105-upping-the-boost/#findComment-1104248
Share on other sites

I'd definately be getting you're outlet (cat-back + front/dump pipe) and cooling (pod filter, FMIC) before doing anything with the boost... This is just the advice I have been given, but I have seen lots of people up the boost without the appropriate support mods and a month or two later, they are forking out for either a new turbo, or an engine rebuild... No thanks.

Link to comment
https://www.sau.com.au/forums/topic/57105-upping-the-boost/#findComment-1104399
Share on other sites

ok I have an HKS 3inch cat back exhaust. Forgot to meention that (sorry) if i was to fit a POD filter would i start getting any idle problems etc etc as I have heard many things about it and am slightly confused if I can just get an adapter so I can slip on a pod filter and thats it? seems to easy?

Link to comment
https://www.sau.com.au/forums/topic/57105-upping-the-boost/#findComment-1104431
Share on other sites

Pod filter wont effect your idle and yes, it's as easy as getting a filter and an adapter to suit.

You can use a cheap bleed valve to increase boost by a couple of pounds but until you get a front mount is wouldn't be going nuts and winding in any more than that.

Link to comment
https://www.sau.com.au/forums/topic/57105-upping-the-boost/#findComment-1104865
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...