Jump to content
SAU Community

Recommended Posts

Hey Guys,

First time poster, but i've been lingering reading for some time. I am currently looking at MY97 RS Four Stageas, and have a few questions.

1) Anyone know any good places for the RB25 and Stagea's around brisbane (workshops, mechanics etc), i would like to get a car checked out before i buy it, are there any telltale signs for these things?

2) i'm a bit worried about kms, everything i've looked at is around the 40k kms mark, which seems a bit low for a 97 model car, is there anything that i can check to make sure kms are legit?

3) how expensive are nissan 4wd systems when they go bad? coming from owning a mid 60's mercedes coupe so parts pricing doesn't scare me, but do they go wrong often?

4) how available are parts? do i need to get someone in japan onside to send me stuff, or is most stuff available through nissan? and where do i find workshop manuals in english?

5) anything i shoud be particuarly careful of buying? preferable models? from what i can tell theres a few engine options, but most i've seen are RB25 RS Four's how do i tell the difference between a Neo and non Neo?.

Thanks in advance for the answers, i hope i don't appear like too much of a noob! hopefully soon i'll have a stagea to post pics of!.

Russ

G'day Russ,

I'll see how I go at your questions.

2. KM's can be a bit sus sometimes. But there are cars out there that have done very low KM's. Check the usual interior items for signs of high wear.. Carpets, mats; seats, steering wheel etc.. They will give you a good indication.

3. I've never actually heard of a ATTESSA system stuff up. I have heard of the very rear case that someone burns out the clutch pack in the centre diff, but it's usually cause they were doing something wrong eg. not disabbling the 4wd correctly, or running different sized wheels/tyres front to back.

4. Parts are available through most Nissan dealers. Prices are pretty reasonable considering. Theres also a heap of parts importers nowadays too.

5. Do a heap of looking around and try and get the best for your money.

I'm actually considering selling mine to downgrade to something cheap so I can use the mony to study part time. Time for a career change...

J

As for NEO & non-NEO, the NEO engined cars were the series 2, which you can tell from the front because they have the headlights with 2 seperate lenses, rather than all in one rectangular block.

Someone with more knowledge than me might be able to tell you in more detail, but that's an obvious difference.

Try http://www.geocities.com/mcnamg/ for more details of models, features, etc.

Mine came with service manuals so I could check the K's and the dates. I also checked the cam belt change date and K's and calculated if the K's were realistic from that. The steering wheel and drivers seat wear rates were also consistent. Most of all I used someone I could trust to source it in Japan.:P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...