Jump to content
SAU Community

Recommended Posts

Hi Guys,

I'm trying to find out what a pair of tail lights are worth and how hard they are to find for these two models skylines.....

The ones I'm talking about are the jap spec ones different to the ones we saw here.....

Are they rare?  Expensive??

Cheers,

Simon

Jap Hr31 tails lights are getting very hard to find indeed, and would fetch a fair price (guess around $170-$200 per light)

Don't know about the Dr30 taillights, but would expect them to be harder to find and most likely more expensive aswell.

There's quite a few people who have given up on getting the old school hotplates for their 31's... If you are thinking about getting a few sets sent over, make sure you get the centre garnish as well. :(

I don't think you'd have much trouble selling them provided they are in reasonable condition.

the late model dr taillights are similar to the S3 r31 ausi taillights ( dr30 ones don't have the smaller section for the indocators and reverce lights at the bottom) next to imposible to find here, the earlier ones the stove tops ones are not quite as hard to find and i wouldn't pay more than $200 for a set unless they were brand new, hint hint....thats what the stove tops look like at night? sort of the like the passage lights pictured about...

damm and i have no money at the moment its always the way... TUFSSS, if your mate can get late model DR ones in that condition at about the same cost them i'd say there would be a few of us here alone that would jump at the chance!

i bought a pair of HR31import lights not long ago ...simply coz tehy were cheap ..but i'm not a fan ..i ended up swapping them for a good pair of Ser3 31 lights instead...

i paid 210bucks including the center garnish and postage from brisbane for them.

I've seen the DR30 ones with the two round circles inside the squares, are these local or JDM?????

All DR tail lights are JDM, i beleive the ones you are talking about there are the S1 tail lights...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
×
×
  • Create New...