Jump to content
SAU Community

Whiteline Camber Kit Squeaks

ADM
 Share

Recommended Posts

ADM Contributor

ADM

Posted
Posted

Hi Guys,

I’ve recently placed the Whiteline adjustable camber kit in the upper control arms of my R32 GTR. The unit seems to be of a high quality and after using the supplied lubricant I had no issues for about two weeks.

It then started to squeak and so I spoke to Whiteline who advised the correct product to use on the supplied grease nipples was Catrol LM grease.

I can only achieve 2-3 days of silent use out of the unit before it starts to squeak.

I’ve now regreased three times. I’ve loosened the bolts off so the grease can penetrate the bushes but that didn’t help.

Has anyone found a long term fix to stop the little buggers from squealing?

Cheers

ADM

Link to comment
https://www.sau.com.au/forums/topic/58068-whiteline-camber-kit-squeaks/
Share on other sites
Mr GTS4 Mentor

Mr GTS4

Posted
Posted

front or rear?

who installed them?

can you see if they are leaking anywhere?

get a heap of that gease take the arms off again, put a heap of it through where the bolts go and make sure the bolt has a layer of grease on it too. and try again.

ADM Contributor

ADM

Posted
  • Author
Posted

I installed them Mr GTS4 and I greased them up good and proper, dagnamit.

The fronts are the squealers I’m using rose jointing in the rear.

I know that I will probably have to take it apart, these units have grease nipples on them and so I’m a bit annoyed that their functionality doesn’t work to the degree where it stops the squeak. I bought them for that reason (instead of the UAS bearing based units). Seems like it might be a design flaw, not good enough when spending the money with a trusted manufacturer.

Any one used the UAS bearing up control arms on the R32?

ADM

Mr GTS4 Mentor

Mr GTS4

Posted
Posted

yeah same thing happened with mine. although i don't know what brand they were because i got them with the car.. start squealing and used the nipple things ( :D ) didn't work. pulled them apart, cleaned them with contact cleaner or something. let them dry them cake them in that special white grease stuff. seemed to work until the bushs were just about to fall out haha.

Sydneykid Grand Master

Sydneykid

Posted
Posted

Hi ADM, I have a Stagea and an R32 GTST with Whiteline bushes (caster, camber and stabiliser bar) both front and rear, that's over 30 bushes and none of them squeek. Is it one side or both? The inner or the outer bush? What alignment settings do you have one it?:D

Sydneykid Grand Master

Sydneykid

Posted
Posted

I use the Whiteline supplied grease, which these days is a white lightweight. The only times I have ever had continual squeeks is when there is metal to metal. I find where that is and eliminate it. Polyurethane to metal sometimes squeeks but that is easy to fix, I just rough up the surface of the polyurethane with a bit of course emery, a bastard file or even a few light knife crosses to hold the lubricant.

The easy way to find th exact source is to jack it up, disconnect the shocks/spring (at the upright usually) and stabiliser bar. Then move the upright up and down. You can quickly find the source with your head stuffed up under the guard. On Skylines with more than standard caster, is it usually the outer upper joint that squeeks. This is because the poly bush distorts and exposes the metal crush tube to the metal upright or upper control arm. The solution is to lightly file the crush tube to allow for the extra caster. No more metal to metal contact and no more squeek.

Sounds complicated, but it isn't really:cheers:

ADM Contributor

ADM

Posted
  • Author
Posted

Nice one, I haven’t checked for that and I am running a "little" bit more castor.

I suppose the grease that I’m pumping into the nipples could be lubricating the metal to metal contact for a short period of time...

Thanks for the lead SK :P

ADM

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
×
×
  • Create New...