Jump to content
SAU Community

R33 Splutter and jump

mulldog33

By mulldog33,
in Engines & Forced Induction

 Share

Recommended Posts

mulldog33 Contributor

mulldog33

Posted
Posted

Hey Guys,

I have recently done some mods to my R33 and am now having a few problems!

After installing a FMIC, Bleed valve(set to 10psi),BOV(Go Fast Bits Stealth fx),

I have had a problem with a splutter when accelerating when hitting 4000 to 5000rpm. After it splutters it kicks in again to red line.

Just recently when driving at low rpm and in low gears it misses completely and jumps then kicks in again. it also stalled the other day when in idle.

Anyone else ever had these symptoms???

Anyone know what the problem could be??? Thanks

Link to comment
https://www.sau.com.au/forums/topic/58182-r33-splutter-and-jump/
Share on other sites
R32Abuser Mentor

R32Abuser

Posted
Posted

hey mate... just had a similar problem with my 32 GTS-T/..... and it turned out it was the fuel pump.... completely shagged itself and needed a new one.... this may b this problem u are having but would pay to chek this as ur first problem

Fly_With_Sky Rising Star

Fly_With_Sky

Posted
Posted

regap your plugs to 0.8mm and it should get rid of your car stuttering, unless the coil pack is screwed. The stall is probably due to the bov, is that stealth fx the one with both atmospheric and plumback ability? If it was at the atmospheric position then thats probably why it stalled.

Do a search as these problems have been covered before.

darrinspencer Grand Master

darrinspencer

Posted
Posted

I installed a GFB stealth just last week to my r33 gtst

Had the same problems

If you read the instructions it tells you to play around with the adjustment until you get it right

I end up with spring pressure about 3/4 stiff and very little atmo

This way i ended up with just enough atmo noise on full boost and stopped the stalling

I have very slight stutter sometimes, will need to do some more adjusting over the week-end.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Komdotkom
      Forced Performance Hta Turbos

      By Komdotkom · Posted

      Thanks for posting, your engine bay looks tops. I'm fairly sure you posted the wrong video though, I think you were supposed to upload the one from your "private test road" where it's banging off the limiter with the gate open?
    • MBS206
      Stagea obd II low voltage

      By MBS206 · Posted

      This is something to be careful of. I did a bit of digging on the NM35, as I spend a lot of time on near brand new cars and CANBus related stuff, which uses the same "OBD2" plug for a fair chunk of making my life easy. The NM35, does NOT support OBD2. The data pin is actually on Pin3, which is a manufacturer specific pin, and requires Consult3 to connect to the NM35. Your low voltage, is either because the NM35 doesn't have 12V to the constant power pin on the J1962 (OBD2) connector, OR, it is attempting the standard comms, (CanBus, K Line, etc) and can't see any voltage on those pins. Some people have had success accessing SOME data from the vehicle on OBD2 specification, using a module that supports KPW. My assumption, like Duncan has stated, it will likely actually be JOBD, where there is some cross over with the OBD2 and JOBD standards. Note, lots of "OBD2" dongles, do NOT support KPW, which is what you need for a lot of Japanese vehicles of this era (And even up until recent years!), EG, Subaru, Suzuki, etc.    The end of this thread is probably worth a read, as some people did find a way to get a display up in the NM35 recently, looks like someone implemented all the stuff needed to make it work. (The right protocols).  
    • MBS206
      Crank Motorsports Front Axles

      By MBS206 · Posted

      Depending on the purpose of the car, and how much more fabbing you want to do, and what clearances you have, you could look to raise the motor, which will raise the front diff up. Likely would mean altering the chassis rails etc etc, hence the more fab work you'd need to do. However, this can create issues, not just in clearance with everything fitting under the bonnet, but you've also raised a LOT of weight up in the car, and this will DEFINITELY alter handling characteristics (But, so will how much weight you've already added to the front end). You'll also have to deal with the fact the gearbox to rear diff is now out of alignment too for the tail shaft, and alter the angle of the diff, or deal with a bit of potential vibration. Raising the motor an inch up, is effectively the same as making the whole car sit higher by not lowering it as far. So one inch higher motor, theoretically means you can drop the car an extra inch lower, and maintain the same angles in the CVs. Again, depends on the purpose of the car. If it's a just cruiser on the street car, maybe won't be an issue. If it's meant to be a time attack car, I can see you not wanting to raise the motor. This is just for you to ponder as an idea.
    • MBS206
      NC MX5

      By MBS206 · Posted

      Have you not seen geospy.ai? It can now give GPS co ords to within a metre from a photo, even if it's a random photo you take inside. Supposedly at the moment only the government/law enforcement has access to that... Supposedly...
    • Komdotkom
      Crank Motorsports Front Axles

      By Komdotkom · Posted

      I've got the rear ones, they're certainly beefy. I need to take them to my driveshaft guru to check over, he's very fussy about the quality of components so I'll let you know if they are made of cheese by a blind man.   Are you in Australia? A mate just had a set of EN26 shafts made for his K20 Lotus by our fabricator which were quite cheap (compared to Driveshaft Shop) so if you can procure the CV's and draw what you need he'd make them for ~$800 for the pair.
×
×
  • Create New...