Jump to content
SAU Community

Recommended Posts

hi i hope someone can help me my r33 has a heater fan problem

the climate control works and the fan works if i take it out and conect

power to it i was hoping someone might know why it doesn't work in

the car or has a wiring diagram any info would help thanks

Link to comment
https://www.sau.com.au/forums/topic/58351-heater-fan-not-working/
Share on other sites

what car is it? if it's a 32 then I can find it in the manual. There's obviously something stopping 12v from getting to the motor. so if you've checked the fuses and relays it would only be the control unit. I don't think there are any other relays for them.

I don't know if you'd have a fan speed switch or where it would be located. It would help to know the car.

what car is it? if it's a 32 then I can find it in the manual. There's obviously something stopping 12v from getting to the motor. so if you've checked the fuses and relays it would only be the control unit. I don't think there are any other relays for them.  

I don't know if you'd have a fan speed switch or where it would be located. It would help to know the car.

sorry I should have read your message a little better. It was late, I was tired.

I will try to look into it.

in the meantime, test to make sure you are getting power to the relay points. Even though the ralay may function, if there is no power to them they won't work either.

same at the fuse and same at the motor.

Basically just follow it back. You may have to unravel the main harness under the dash but the wire colours should remain the same so it shouldn't be too hard to find.

  • 2 weeks later...
  • 3 months later...

i found the problem on my heater fan. if you pull the glove box out, you will see a plug with 2 or three wires dead central to the opening you just created. there will also be two screws holding a mudule that is attached to the plug. this module controls the fan speed using a complicated circuit board, i got a second one and put it in works 100% now

  • 9 years later...

FYI - Had this issue also today in my girlfriends 95 r33 gist series 1.5.

I pulled apart blower motor

ran 12v directly to it - it ran fine

checked all fuses and relays - all worked fine.

identified the module discussed above. thought to myself...wonder if r32 is the same (have an r32 race car with no a/c - i located the module - looked different. had different part number but plug was the same and it directly fitted. Turned back on climate control..and heater fan worked...!

So FYI can use r32 item in r33.

Cheers.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A 1.5 way is a 2 way. It is just a 2 way with a less aggressive ramp on overrun.
    • The ABS and/or TCS being missing/broken will not cause the engine to misbehave. It just casues CEL to come on and annoy you. The CEL is useless if it is always on, so you have to do the things you have to do to get rid of it, so it can be useful. Being a Stag ECU, then yes, it will not expect TCS to be present. But it will expect ABS to be present and working. You will need to either make the ABS CU talk to the ECU (don't ask me what that will take on an NA R34), and make sure the hardware is working....or, you just need to blank it out in Nistune. Do not persist with the stock ECU. You will just have problems. Gte it Nistuned. Start from there. DO YOU HAVE A BOOST SENSOR? The ECU's boost sensor that it. It is connected to the loom at the rear of the coil cover. Usually rides on the firewall on an R34, but is usually bolted down to a bracket along with all the other crap at the back of the coil cover when a Neo is dropped into another car. If you do not have it, the ECU will shit the bed. So, do you have one?
    • So sadly the fuel pump etc was not it. The pump and filter is new and it is still cutting around 4000 rpm. A read something about ABS/TCS (engine is from stagea and ECU too so no TCS) and i dont know for 100% that my car has ABS. It has ABS "cube" in engine bay but i dont think it works(or at least from my braking experience). Can be something like that?  I will be driving the car next week to Nistune tuner to properly see what is wrong...  
    • the Tomei LSD fluid with lsd kit. frustrated that it was shaking the car to crap and affecting everything else negatively, I pulled the diff last night, and removed the lsd carrier, could not find anything wrong, however it seem to be 100 locked up acceleration, and deacceleration, wondering if they sent me a 2 way not a 1.5??  either way I installed the stock open carrier back in place. test drove everything smooth as butter again. no shake, shutter, random, what felt like clutch slip and grab or drive shaft play, etc. something differently wrong in side the lsd. I might bother taking it apart (if possible) to figure out what's going on inside this carrier, as bought too long ago to return.  only draw back is its back to a one wheel wonder.
×
×
  • Create New...