Jump to content
SAU Community

Recommended Posts

Thought I would start a Stagea Intercooler thread, so here goes

The stock Intercooler placement is CR*P, and so relocation/replacement is

a viable option

I see lots of 600x300x76 coolers, is there enough room for one of these

or is a 2nd hand GTR cooler a better bet.

Any hints on piping etc, how easy to do

Many thanks

Link to comment
https://www.sau.com.au/forums/topic/58586-stagea-intercoolers/
Share on other sites

Enough room for a GTR cooler - fills up the front bar nicely. About 25% of it is wasted though - sits up quite high. I would recommend a second hand gtr cooler - excellent flow.

Ken

Enough room for a GTR cooler - fills up the front bar nicely. About 25% of it is wasted though - sits up quite high. I would recommend a second hand gtr cooler - excellent flow.

Ken

Cool

How difiicult to fabricate/route the piping (no cutting of panels I hope :Oops:

A hole saw is need for the box under the battery, you need a hole there to run the piping. Be prepared to find a new washer bottle too - that gets in the way. You are probably better off getting a r33 ic kit, should bolt up without a problem.

Cheers,

Ken

Depending on your power goal, Trust make an replacement intercooler that sits in the stock location.

Three times the thickness, MUCH better end tank design, and it flows heaps better too.

I'm not sure how much power it will support, but if your after a mild setup it might be worth looking at (secondhand). You may be able to pick one up for the cost of just the pipework on a FMIC.

J

Depending on your power goal, Trust make an replacement intercooler that sits in the stock location.

 

 Three times the thickness, MUCH better end tank design, and it flows heaps better too.

 

I'm not sure how much power it will support, but if your after a mild setup it might be worth looking at (secondhand). You may be able to pick one up for the cost of just the pipework on a FMIC.

 

 J

Now THAT sounds like a plan. I'm interested in anyone that has a lead on one of these units.

Based on the Trust website, there is no specific Stagea cooler, but there are genuine replacements for the R33 & 34. I was under the impression that the C34 intercooler mounting is the same as R34. Can anyone clarify that?

I can clarify that the R33 GTS-t Trust side mount intercooler is a near perfect fit on a 96/97 Stagea cause that's what's on mine at the moment.

The top and back mounting points line up perfectly, although the front mounting point doesn't cause the Stagea's tow hooks are located further rearward compared the the R33's. Although the two mounting points (the top one in particular) makes it very secure. Remember that the two hoses help hold the cooler there too.

The only other thing I had to do was trim about one inch of plastic off the inside of the front bar. Mind you, when you put the black plastic wheel arch thing in you can't even see where I trimmed the plastic !!

I noticed a noticable difference in responce and power when I put it in. I wouldn't say it gave me a million kw at the wheels, but there was a definate difference.

J

I can clarify that the R33 GTS-t Trust side mount intercooler is a near perfect fit on a 96/97 Stagea cause that's what's on mine at the moment.

The top and back mounting points line up perfectly, although the front mounting point doesn't cause the Stagea's tow hooks are located further rearward compared the the R33's.  Although the two mounting points (the top one in particular) makes it very secure.  Remember that the two hoses help hold the cooler there too.

The only other thing I had to do was trim about one inch of plastic off the inside of the front bar.  Mind you, when you put the black plastic wheel arch thing in you can't even see where I trimmed the plastic !!

I noticed a noticable difference in responce and power when I put it in.  I wouldn't say it gave me a million kw at the wheels, but there was a definate difference.

J

Hi J, was the standard Stagea intercooler the same as a R33GTST or R34GTT?;)

Mercury Motorsport just fitted a FMIC to the stagea. Fits behind the grill without any choping into it. The only thing they had to do was take a little slice out of the re-enforcing bar. They did a damn good job.

Cheers

Gary

The 'cheap' upgrade I read about was to fit the 25GTT cooler as it was a better design than the GTS25T unit. FYI, the Trust webby with all the models available is: http://babelfish.altavista.com/babelfish/t...cooler_kit.html

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...