Jump to content
SAU Community

Recommended Posts

From where I come from(East Malaysia), the A31 is the only car that is still readily available.Hardly if not never, heard of the 260RS..hehehe... Furthermore, I know most of you dudes here use the A31 for drifting but I'd like a sleeper with an RB26 and 4WD in it(straight line beast). As for the 4WD system, I think I'd forget about all the wiring hassle and opt for the Veilside or APEXi torque split controller...unsure how much they cost though.

Speaking about cost, I can keep the labour rates low as I deal with many workshops almost everyday who can give me good deals.Furthermore, I do have my own mini workshop at my backyard(my dad's also an enthusiast).

If I see a huge possibility of converting the A31 into an RB26DETT/4WD beast, I'll set aside some $$ for it to happen sometime soon. What's holding me back is the modifications to the chassis that is needed to fit the gearbox/ATTESSA system(wider) as well as the front suspension and front subframe/crossmember to clear the moving parts..

FYI, the A31's price over here stays at around AUD 15k. How much is it over there?

from what ive seen its possible based on the one i seen for sale not long ago... had RB26 engine, box and 4WD system... i just dont know how hard it is to do.

so if u do end up doing it... take lots and lots of pics as u progress and keep us informed ;)

hehe I'm supposed to be in malaysia right now holidayin in KL... anyways... the cefiros in KL are all the RB24S carby versions arent they? I think I saw a few N/A RB20 ones but most of the souped up ones had 1JZ's in them. The Malay ceffies are a bit different to the Jap ones in that the brakes and suspension are a lil different.

An A31 landed and registered in australia can cost anywhere between 12kish for a good clean stock or mildly modified automatic (like the one my dad drives), about 9k for a used and abused drift pig, or a purposely built full tuning house car like inark RB26 ceffy (built by Ken Works as a drift "practice car") will cost you in excess of 16k without compliance and registration which should tip it at about 20k all up.

Mate, you're in KL(West Malaysia)?

Actually there are two types of cefiro's available here, the shitty locally assembled ones and the japanese imports..hence the difference you saw.

Many cefiros in KL are fitted with the 1JZ-GTE engine as they are easy and cheap to get .. and basically straight forward unlike an RB26 where you need to get an RB25 or VG30 box to drive the car.

A friend told me there's an NA31 in KL. He was hanging out at some friend's workshop when he saw a cefiro up the hoist...went underneath it and saw driveshafts at the front.Sadly the car is not for sale...

I got some family in KL, and also dispersed in Penang, Sarawak n stuff and also a handful in Singapore etc so I visit from time to time. GF's 100% malaysian indian, she's up there atm.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
    • To drain the Intake Heat Exchanger, there is a crappy drain plug in front of the driver's side front tyre: You should use the largest headed phillips screwdriver you had, and in my case I needed vice grips on the hose above as the plug was tight (tighter than it needed to be, since it has an o-ring seal).  After you have a tray down and open the drain, open the intake heat exchanger reservoir cap (drivers side one) and you should get a couple of litres of coolant To get to the radiator, you need to remove the plastic engine undertray. It is held on with a series of 10mm headed bolts and some clips. For the radiator, there is another type of crappy drain (kind of like a plastic banjo bolt) and you should attach a length of hose to direct the stream of coolant per this pic (otherwise the coolant hits the rad support and goes everywhere). The drain is on the rear of the radiator on the driver's side and a bit hard to find. Put a big tray or bucket down (5l won't be enough) and slowly unscrew the fitting by hand. You only want to remove it far enough for coolant to flow, it you unscrew it right out the whole fitting and direction pipe will come off and you will get a coolant bath (yum!). Undo the radiator reservoir cap and it should empty about 8l
    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You also need to drain the intake heat exchanger to remove the radiator so you will need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. 2 other tools that really help dealing with coolant lines and spring clamps are Bent Needle Nose pliers Hose pliers Between them they will reduce the frustration (and injury) potential by about 1000% Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
×
×
  • Create New...