Jump to content
SAU Community

96 Series 2 Skyline** Cheap** MUSt SELL

Husky33
 Share

Recommended Posts

Husky33 Veteran

Husky33

Posted
Posted

Hey guys,

1996 Series 2 R33

White

87000km

5 Speed

Air con works perfectly

NEVER BEEN BOOSTED. Has always run stock boost(6-7psi)....i hardly ever give it some and NEVER EVER go over 2500rpm until the car is warm

BODY

Nismo 400R sideskirts

The spoiler is off atm but the car comes with the spoiler, fitted if u like.

ENGINE

Apexi Power Intake filter

HKS Super Dragger exhaust from Turbo back

BLITZ LM fmic purchased brand new 2 weeks ago(not fitted in pics)

GReddy oil cap

ROLLING

Slotted rotors front and rear

17" BLEST rims with dished rears...mmmmm

235's on the front and 255's on rear with good tread

KYB springs n shocks

Front and rear strut bars

Front brake pads in good condition and recently relinnished

INTERIOR

VDO boost gauge

Razo gear knob

Super bright white headlights bulbs

SOUND

Kenwood double din headnit

Upgraded speakers in the front doors

This car, with just the stock intercooler, pod and full exhaust has made 143.4rwk on...yes...6psi!! on Protek's dyno. It now has the Blitz LM fmic and feels more powerfull and heaps smoother. Still runs stock boost though, around 7psi :flamed:

Oil and oil filter changed every 4000km's, spark plugs every 5000km's and gearbox oil and differential oil every 10000km's. I am not joking either, whenever i get bored i service my car :headspin:

Motul 300V oil just put in last week along with a new oil filter and BCPR6ES spark plugs, brake, diff and gearbox fluid all changed about 6 weeks ago and the front pads were relinished at the same time. The afm was replaced with another low kay series 2 one about 3 m0nths ago.

There is a hairline dint in the drivers door, it is very clean and can be pushed out no worries. There is a bit of wear on the dash just above the middle airvents as when it came over from japan there were four gauges stuck on the dash which have now been removed.

This car was imported by Delrich Lane importers at the beginning of 2003.

Rego till late august

Price is 19,800 <---- Series 2 for this price,,,craaazy

Reason for selling is i'd like to get a cheaper car so i can start to concentrate on career options

00006916fu.jpg

00006926pz.jpg

00005401lx.jpg

00003865dr.jpg

00003886al.jpg

00007022el.jpg

00000207rc.jpg

00000225ne.jpg

Wear on dash

00000254ks.jpg

Hairline dint

00000332no.jpg

0000671small8jq.jpg

Link to comment
https://www.sau.com.au/forums/topic/60226-96-series-2-skyline-cheap-must-sell/
Share on other sites
Husky33 Veteran

Husky33

Posted
  • Author
Posted

Price drop to 19,800...farken crazy arent I? Cmon guys, it's not a dodgey car, easily one of the best lookin r33's in Victoria( u have to see it to understand)

But yeah it just has to go guys,, financial problems

  • 2 weeks later...
Husky33 Veteran

Husky33

Posted
  • Author
Posted

umm with the springs/shocks it sits pretty low...the cooler piping that runs back udnerneath hte cooler sits abit lower than the front bar. but iu have stock springs that come with the car so u could chuck them on if ya want

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • TurboTapin
      new 1.5 LSD issues/concerns

      By TurboTapin · Posted

      My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • MBS206
      NC MX5

      By MBS206 · Posted

      Bunnings would have just handed you your money back on that one!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...