Jump to content
SAU Community

Recommended Posts

i have a r32gtst. when i go for a drive, for the first 3 minutes the turbo makes a spool and sucknig noise but it has no affect on excelleration. when the car is running after 3 minutes the turbo kicks in and works fine. However some days i can be driving for say an hour and suddenly i will take off and the motor will make noise like its running really hard and the turbo wont spool. 2 minutes later it will be fine again. anybody have any ideas? (this isnt what you call shaft play is it?)

ps, i dont know bout boost coz my gauge is not and has never been hooked up.

Link to comment
https://www.sau.com.au/forums/topic/60724-turbo-not-spooling/
Share on other sites

Similar thing happens to me in my 33. Only in the higher gears tho. Sometimes if im in say 5th gear and i accelerate from 2000rpm when it boost comes on the revs will rev hard but the car wont accelerate at the rate of the revs.

Not sure what it is maybe spark?

my 33 does that too, on higher boost it does it worse and coughs and splutters, ive put it down to coils and am getting some 2nd hand ones this week, if that fixes it ill get some splitfires. it started after runnin 1bar for 3 days, so i wound it back to 12psi untill it started to do it again, im runnin 7psi now and its starting to do it again, so i think its coil packs breaking down.

ive checked all the intercooler pipes and hoses, and vucuum lines, and also the turbine and compressor wheels.

ill let you know how it goes

cheers

Linton

my 33 does that too, on higher boost it does it worse and coughs and splutters, ive put it down to coils and am getting some 2nd hand ones this week, if that fixes it ill get some splitfires. it started after runnin 1bar for 3 days, so i wound it back to 12psi untill it started to do it again, im runnin 7psi now and its starting to do it again, so i think its coil packs breaking down.

ive checked all the intercooler pipes and hoses, and vucuum lines, and also the turbine and compressor wheels.

ill let you know how it goes

cheers

Linton

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The spray cans were in the "Kiln" room whilst I was preping the parts,  so probably around 2 hours to get them warmed up, the kiln room has 3 small ovens running at 100°c, 3 medium sized ovens running 100°c, and the large one I used running at 80°c, the room itself was about 28°c, I also spent a bit of time taping up the parts in the room as well, and by the time I was done I would assume that the parts were around that 28°c As for power, I expect a couple of Killerwasps up high would be achievable with the current mods, I'm still running the MZR 2.0 intake and throttle body, and there is a slight mismatch with the 2.0 intake (smaller) and 2.5 intake ports (larger) on the head, this intake is matched and specifically designed to fix this issue with the ports mismatch, the throttle body is also a couple of mm larger, OEM is 65mm, the Bosch is 68mm In the end it will look "prettier" than the molded plastic thing that is the OEM MZR 2.0 intake As for the LSD, it's the OEM Torsen which works fine for what I use the car for, plus, basically no maintenance apart from the occasional oil change
    • I was at Tunehouse in Marrickville (great team over there really know their VR's) , and I spotted this Very clean R35.  
    • Mate , I have the same issue right now with the exhaust noise , if you can tell me what your local guy did , I'll talk to my guys and see if they can do the same. Power is good but it just too loud when put it down. 
    • The other trick I've found with wrinkle black is to put the can in hot water for a bit to warm the paint up, and to pre-heat whatever you're painting. It'll be interesting to see if you pick up any power with the intake, following with interest. Got a proper lsd for this?
×
×
  • Create New...