Jump to content
SAU Community

Recommended Posts

Hi,

Does anyone know the correct procedure for cleaning an HKS pod filter, the yellow one that looks like a big mushroom?

I have cleaned it out using the solvent part of the K&N kit, but I am wondering if it requires an oiling??? I don't think it does but if anyone knows please let me know.

Thanks in advance.

Sam.

Link to comment
https://www.sau.com.au/forums/topic/60959-cleaning-hks-filter/
Share on other sites

Hey BlueTwo....

Ive also got a HKS pod, except its got the green element..

These should not be cleaned - but replaced.

They come pre-oiled, and dont take too well to washing/cleaning.

Depending on driving conditions, i would change it every 15/20k...

Cost is about $70 from autobarn...

:D

Hey Gizmo,

Do you know if there is any difference between the green and the yellow one? The yellow one looks like a big sponge, with what seems to be a good capacity airflow through the matrix of fibres, quite a bit different from my panel K&N with it's cotton insert.

...The flow of the HKS is one of the best when compared to others..

However, regarding pods as well as any other filter - more/better air flow usually means less protection filtering elements.....as attested to the pod noise !!

So - conversely, the HKS pod filter also isnt one of the best in regards to protection. Its your choice what you are after.

Every 20k i also check the AFM and tubing for any particles - so far it is ok, but you need to change it at least every 20k to ensure you dont get any nasty surprises..

colour difference is mainly for show - however, some colours only come in some sizes...it all depends on the size of your pod..

http://www.hksusa.com/products/?id=787

:D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bummer...yeah i "need" something to "ease" up the work and for my driving it would be enough.    Iam counting the tune "without" turbo. I do not mean "cheap" like something from Temu around 200 USD, "Cheap" is something around 1000 USD? 
    • Starter motors used to use the weight of metal (magnets) to provide torque. Now they use (more) current instead. This. It's completely normal.
    • So thing that had me stumped, but I think is OK....is that when it was up in the air, in neutral I had it running to bleed to coolant while I put the wheels back on. I noticed the rears were turning (slowly) which I'd never seen before 20250928_163512.mp4     Because there had been an issue with clutch slip due to pedal adjustment on the dyno, I assumed there was still and issue so spent some quality time upside down under the dash adjusting the pedal....but no matter what I did the wheels still turned in neutral. Even disconnected the master cylinder to pedal rod and same. In despair, I even removed the clutch slave so there was no chance of any preload causing it.....still happened. So either: 1. Something is not right in the bellhousing, or 2. Its a thing sometimes with cold, thick gearbox oil Internet says it might be 2, I hope so!
    • OK, few more things sorted and it is ready for a shakedown on 10-Oct, with one weird thing. Changed the run in oil and filter for the good stuff. 8l came out, about 8.5 went in with filter so that looks all good. Changed the starter (again), this time for a brand new one, works good. Interesting that the Taaaarks one is shorter than factory but spins harder, I guess electronics have moved on a little in the last 30 years. Will be nice to have a bit of extra space under there. Put the timing cover back on, and noted where the cam gears were set as a record.  Will need to double check the timing but it is pretty close. Also put the coil pack cover and intake snorkel back on. Exhaust Inlet Changed the water out for coolant, bled up nicely. Removed the rear brake pads (well worn factory sumitomo ones!), gave the hardware a good clean and reassembled. I've put bendix XP on the back again because the price is excellent at $150 a set and they worked well on the V37. Front pads have plenty so no issue there
×
×
  • Create New...