Jump to content
SAU Community

Replacing your pushrod tube oil seals in your LS1 V8 (a must read)

gen4_v8

By gen4_v8,
in Tutorials / DIY / FAQ

 Share

Recommended Posts

gen4_v8 Rookie

gen4_v8

Posted
Posted

Pushrod Tube Oil Seals

Leaky pushrod tube oil seals are a common cause of oil leaks on the VW air-cooled engines. To fix the leak, you have to remove the pushrod tubes and replace the seals on both ends.

It's not a technically difficult task, but it is time-consuming and will try your patience. It will be easier to do the job with the rear wheels removed.

NOTE:This procedure applies only to the Type 4 engine. To replace the pushrod tube oil seals on a Type 1 engine is much more involved, since the cylinder heads have to come off.

To remove the pushrod tubes,

1) Remove valve cover -- get your big honkin' screwdriver under the bail and pry it down (don't pry it up. You'll regret it. Ask me how I know).

2) You are now faced with your rocker arms. Note that there is a thin metal wire spring thing that is very oddly shaped and goes the length of the head, fitted under the rocker arms and holds the pushrod tubes in place. Pay attention to how it goes because you will need to know later. This is another reason for doing only one side at a time so you can reference the other side for reassembly. Anyway, loosen the rocker arm nuts a bit so you have enough slack to get that spring out. Try not to bend it up too much.

3) Get a clean paper towel or something similar to keep all the parts on. Put the spring on the towel. Now remove the rocker arm nuts and washers and put them on your towel. Don't lose 'em. Pull the rocker arms off the studs and be careful as they will want to fall apart as soon as they are free from the studs. Put them on the towel next to each other like they are in the engine. This is one of those jobs where you want to avoid mixing stuff up.

4) Remove a pushrod (I do these one at a time so I don't get the pushrods mixed up. Just pull it right out. Sometimes they are full of oil and surprise you. Lay it on the paper towel, make sure it's straight by rolling it. If it's bent, time for a new one.

5) Remove pushrod tube. You do this by twisting/pushing/pulling it out through the cylinder head. Many say not to use pliers on the tube but if you use pliers and squeeze lightly (so as not to crush the tube) you'll be OK, I used pliers when I did it and they're MUCH easier to get out that way. Just be sure to squeeze very lightly. You usually need to set up a twisting motion to break them free and then pull back firmly but gently and pull the tube out through the head.

6) Clean up old tubes or replace them. Use parts cleaner, like brake parts cleaner or carb cleaner. Get all the crud off the tubes, you may find that they are not supposed to be black. You may also elect to purchase a complete set of new pushrod tubes. Remove the old seals from the tubes if you are reusing them. I usually get them off by getting a screwdriver blade under the seal and prying it off the tube.

7) Install new seals. There are two kinds available. One is the stock VW seal and the other is the seal that gets used on the Porsche version of the same engine. Buy the expensive Porsche version. Word is they will outlast the VW seals quite well. You will need 16 seals for the job and the seal for the case end of the tube is smaller than the seal for the cylinder head end. So you should have 8 of the large seals and 8 of the small.

8) Clean up the sealing surfaces on the cylinder head and the engine case. Use a paper towel moistened your parts cleaner of choice. Be thorough, any dirt on the sealing surface will cause leakage. Take your time and do it right.

9) Repeat with each pushrod tube.

10) Put everything back together. When reinstalling the pushrod tubes, you need to make sure they seat all the way. They don't tend to want to go all the way in by hand. I used a big 1/2" drive extension as a drift and gently tapped the tubes home with a hammer. Be careful doing this that you don't pinch the seals on the head end.

Make sure that you put that wire spring thing back in correctly. It holds the pushrod tubes in place. Again, don't mix up the pushrods, rockers, etc. Also, when putting things back together, you will want to make sure that the pushrods seat correctly in the lifters. If you twist them around by hand you can just feel them slip in where they're supposed to be. After you're done, put new valve cover gaskets on (don't use sealer, just a thin coat of wheel bearing grease on both sides of the gasket). If the sealing surfaces for the valve cover gaskets on the heads are rough, it is wise to take some steel wool and use it to smooth the cylinder head surface out. This will stop those pesky valve cover gasket leaks. If you have solid lifters, you will need to adjust the valves after this operation (that's another whole procedure, but is written up well in Muir). Some say if you have hydraulic lifters you also need to adjust but I've seen it done without adjusting and it's been fine.

I hope this helps someone else as much as it helped me. If you need further instructions please pm me or reply to this thread.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Recommendation for engine oil funnel spill free

      By MBS206 · Posted

      I thought I'd come back and add something I JUST learned. A Toyota LandCruiser with a 1HZ, mates perfectly with a bottle of Nulon brake fluid. As in, it perfectly screws in. Great make shift funnel when you cut the bottom of it off. This may work for your Corolla.   Unfortunately, tipping a 10L drum is much harder than a 4 to 6L bottle, and they no longer include the easy pour tap which was just perfection to use previously.  
    • EndZee
      Fuel Pump Control Module & Dropping Resistor

      By EndZee · Posted

      Guys since i bought r33 gts25t coupe 1994 automatic a/t(manual swap 350z gearbox)  all i got is problems, always problems. Lets start with that when i turn key into ignition(ON) fuel pump doesnt always works. Sometimes i have to turn key twice Off/on/off/on until it primes. Its new, dw300 - 340lph. My gearbox broke so i did gearbox swap, install different intake manifold, injectors and i take pipes. Car was sitting in garage for more than half a year. I did assembly all not that long ago and when i turn ignition cant hear prime. All of sudden it stopped working. Theres many videos on YouTube how to make relay mod on r33 straight from battery so i did and it doesnt work! 😰 30 - battery positive  87 - positive from fuel pump to relay 85, 86 - one of two wires from original fuel pump wires(light blue, grey) and it didn’t work. so I check on ignition and took original BLUE relays wires from trunk, next to fuses. (I believe it’s IGN+ and ECU pin 18. it didn’t work…  tried connecting (IGN+ from og relay) and (ECU 104 from 1of4 FPCM wires) to my new relay 85/86 and it didn’t work.  I unplug FPCM. Didn’t work. im thinking what’s wrong   fuel pump is working, if I leave IGN+ on 85 and 86 straight to ground it works but it’s just nonstop. Since it getting constant 12v after key in ON. light blue wire gives me 6-8v.  so how this should be connected? What causing ECU not giving — on pin? Or I did sth wrong and that’s why it doesn’t work? I need negative signal on ECU that control fuel pump. What this should be?
    • Duncan
      M35 Brake caliper replacement

      By Duncan · Posted

      You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Duncan
      Most women will agree that parking is the most taxing part of driving

      By Duncan · Posted

      Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Duncan
      Jacks that fit under GTR lips that can reach the subframe?

      By Duncan · Posted

      Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
×
×
  • Create New...