Jump to content
SAU Community

Replacing your pushrod tube oil seals in your LS1 V8 (a must read)


Recommended Posts

Pushrod Tube Oil Seals

Leaky pushrod tube oil seals are a common cause of oil leaks on the VW air-cooled engines. To fix the leak, you have to remove the pushrod tubes and replace the seals on both ends.

It's not a technically difficult task, but it is time-consuming and will try your patience. It will be easier to do the job with the rear wheels removed.

NOTE:This procedure applies only to the Type 4 engine. To replace the pushrod tube oil seals on a Type 1 engine is much more involved, since the cylinder heads have to come off.

To remove the pushrod tubes,

1) Remove valve cover -- get your big honkin' screwdriver under the bail and pry it down (don't pry it up. You'll regret it. Ask me how I know).

2) You are now faced with your rocker arms. Note that there is a thin metal wire spring thing that is very oddly shaped and goes the length of the head, fitted under the rocker arms and holds the pushrod tubes in place. Pay attention to how it goes because you will need to know later. This is another reason for doing only one side at a time so you can reference the other side for reassembly. Anyway, loosen the rocker arm nuts a bit so you have enough slack to get that spring out. Try not to bend it up too much.

3) Get a clean paper towel or something similar to keep all the parts on. Put the spring on the towel. Now remove the rocker arm nuts and washers and put them on your towel. Don't lose 'em. Pull the rocker arms off the studs and be careful as they will want to fall apart as soon as they are free from the studs. Put them on the towel next to each other like they are in the engine. This is one of those jobs where you want to avoid mixing stuff up.

4) Remove a pushrod (I do these one at a time so I don't get the pushrods mixed up. Just pull it right out. Sometimes they are full of oil and surprise you. Lay it on the paper towel, make sure it's straight by rolling it. If it's bent, time for a new one.

5) Remove pushrod tube. You do this by twisting/pushing/pulling it out through the cylinder head. Many say not to use pliers on the tube but if you use pliers and squeeze lightly (so as not to crush the tube) you'll be OK, I used pliers when I did it and they're MUCH easier to get out that way. Just be sure to squeeze very lightly. You usually need to set up a twisting motion to break them free and then pull back firmly but gently and pull the tube out through the head.

6) Clean up old tubes or replace them. Use parts cleaner, like brake parts cleaner or carb cleaner. Get all the crud off the tubes, you may find that they are not supposed to be black. You may also elect to purchase a complete set of new pushrod tubes. Remove the old seals from the tubes if you are reusing them. I usually get them off by getting a screwdriver blade under the seal and prying it off the tube.

7) Install new seals. There are two kinds available. One is the stock VW seal and the other is the seal that gets used on the Porsche version of the same engine. Buy the expensive Porsche version. Word is they will outlast the VW seals quite well. You will need 16 seals for the job and the seal for the case end of the tube is smaller than the seal for the cylinder head end. So you should have 8 of the large seals and 8 of the small.

8) Clean up the sealing surfaces on the cylinder head and the engine case. Use a paper towel moistened your parts cleaner of choice. Be thorough, any dirt on the sealing surface will cause leakage. Take your time and do it right.

9) Repeat with each pushrod tube.

10) Put everything back together. When reinstalling the pushrod tubes, you need to make sure they seat all the way. They don't tend to want to go all the way in by hand. I used a big 1/2" drive extension as a drift and gently tapped the tubes home with a hammer. Be careful doing this that you don't pinch the seals on the head end.

Make sure that you put that wire spring thing back in correctly. It holds the pushrod tubes in place. Again, don't mix up the pushrods, rockers, etc. Also, when putting things back together, you will want to make sure that the pushrods seat correctly in the lifters. If you twist them around by hand you can just feel them slip in where they're supposed to be. After you're done, put new valve cover gaskets on (don't use sealer, just a thin coat of wheel bearing grease on both sides of the gasket). If the sealing surfaces for the valve cover gaskets on the heads are rough, it is wise to take some steel wool and use it to smooth the cylinder head surface out. This will stop those pesky valve cover gasket leaks. If you have solid lifters, you will need to adjust the valves after this operation (that's another whole procedure, but is written up well in Muir). Some say if you have hydraulic lifters you also need to adjust but I've seen it done without adjusting and it's been fine.

I hope this helps someone else as much as it helped me. If you need further instructions please pm me or reply to this thread.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...