Jump to content
SAU Community

E-Manage issit!

G0DF4Th3R

By G0DF4Th3R,
in Western Australia

 Share

Recommended Posts

shoey_R33 Contributor

shoey_R33

Posted
Posted

hihi, im about to purchase the e-manage as well... question is, do i need to buy the CD and cable? or would the tuner have them?

btw i only have until tomorrow to get it in hk for a reasonable price (arnd $400aud for the base unit)....so i dont have enough time to read through all the posts to do real hardcore research ...

32vspecII Mentor

32vspecII

Posted
Posted
i have had no issues with my auto operation in over 2 years at the above power levels, shifts have always been spot-on and tight, no flaring,nada.....maybe its coz i drive it like grand ma  ;-)

rev-limiter  wots that...babababa...ohh THAT!!

Cheers,

Michael

your milage may vary . My auto has changed operation slightly since just upping the power with the stock ecu . It kicks down to frequently , is harder to hold gear and changes late . Obviously if you change the load that goes into it its going to operate differently . It could also vary on the condition of the gearbox , my old 100k r33 slushy might no longer be in very good nick compared to a newer and tougher designed r34 triptronic .

however people drive around with crazy shift kits in their auto and live with it so its still a viable option for some extra power .

666DAN Grand Master

666DAN

Posted
Posted

I don't think you could get much further than the factory tune with my one...I'm running the 25GT ECU..with a turbo :cheers:

The auto shifts just fine, only flares if the revs creep too high when the car is cold...after that it changes just fine...that's with the 25GT tiptronic...I've got 6 clutch plates instead of the GT-T's 7 plates.

Also I've done 150,000Kms in this car now

masTers Mentor

masTers

Posted
Posted

Ill probably order;

Greddy Emanage Unit

Injector Harness

Ignition Harness

Knock Sensor

Pressure Sensor

Thats all i should need yes? Also can anyone lend me the tuning software and cable so my workshop can tune it.?

N I B, can you pm me a cost to tune the emanage?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...