Jump to content
SAU Community

Recommended Posts

and where is the A/C Grommet in a coupe r33 :P like i said, i duno wanna take out dash or anything... its for a boost guage... ps... wheres a good place to put a 2 1/8 gauge [yeah it was too big thinking dash is mad... but now wid vic laws i think ill have to sell it and lose big bucks ;/

the boost gauge? is it electric one or normal.

My boost guage hose is fairly big, so when i did mine. I ended up drilling a hole next to the master cylinder.

Then ended up mounting the boost gauge on the a pillar as low as i can with the pillar gauge.

Pop your bonnet...

Look at the turbo.. Now lok directlly behind it at the firewall. You will see two silver pipes going threw the firewall. Just below that you will see a wiring harness about an inch think coming threw a big ruber grommet. Now pass a broken coat hanger threw the rubber grommet. Find it on the inside and then tape the pipe on the other end of the coat hanger. Then lube it up a bit with some dish washing liquid. Now pull the coat hanger all the way threw. Now you have what you want threw the firewall....

You need to use the coat hanger cause you cannot see the ruber gromet from the inside. You need to rely on feeling with you hands in behind the ac evaperator...

Cheers

Omg, thanks so much for that col-gtsx. see, the problem is, i've been passing wires through the right hand side - near the accelerator. The grommet is like really tight, so i've just squeezed the wires through the edge, which is pretty dodgy. I find they get cut in a few months from getting rubbed on the edge.

I've had a look at the main grommet which you speak of. I notice that the grommet is also very tightly squeezing onto the loom. How do I get stuff through it without wrecking it, or cutting it? or do I just have to make a small hole in it and poke the coathanger through? I don't want water leaks

I cut a small hole beside the main loom in the rubber.. As the hole in the fire wall is over 2 inches big... You will have to submerge it in water to get it to leek.... And if you did that, you have a lot more to worry about before you would notice or care for the little ruber grommet.. LOL

Make sure you lube the item up and tape it too the coat hanger so you can pull hard...

(I can see that above line looks really sus...)

But yeah if you dont lube it you will tare the rubber or the item taped on the end will fall off...

yeah, I got it. I know exactly what you mean now. My problem was I didn't wanna break the end rubber. But like I said above, now I realise that was stupid.

And then how you need to use lube, other wise, it gets caught on that rubber tubing that runs to the other side.

Thanks so much for your help mate. It's sorta harder to do on skylines isn't it. On toyota soarers, they've actually got a little grommet about 2 cm wide that go straight (not offset) through the firewall. That's big enough to pass just about everything through.

Thanks again col gtsx and all others.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for all the replies fellas. Gonna finish putting it back together and see how it handles the set up. If it starts pinging it’ll be parked.
    • Well, I can recommend the partial AV system translation CD I ordered from Car Audio Workshop in NZ. Whilst it didn't address the date issue, it has conveniently translated on-screen menu items into English, and now allows the GPS-received time to be offset in hours rather than minutes, so I can display Eastern Australian time accurately ( and bump it by another hour when daylight savings starts ).
    • Yuh, if it's 45°C outside, my car is driving in it.
    • I'd be curious to hear more. Otherwise, have you driven a modern x-trail? I wonder how it compares. Here in Australia they are/were popular for rentals and fleet vehicles. I have been in some and my impression was they are bad. But, this may have been very different in the 2000s at a good trim level. Twenty years is plenty of time to make the model worse. I do very much agree with the 2 silver cars in the garage approach. But, not driving because it's too hot would not leave a lot of time in the year for many Australians. I don't think you need to worry too much unless the car has actual issues with overheating. 
    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
×
×
  • Create New...