Jump to content
SAU Community

Differences between R32 GTS-4 and GTR

BCRBT
 Share

Recommended Posts

BCRBT Newbie

BCRBT

Posted
Posted

Hey all, noob here....

Did a bit of seraching and i would like to know the differences between gts-4 and the gtr (R32 of course).

Apart from the obvious engine differences, RB20 to RB26, i was wondering if the drive train is the same ie gearbox and diffs etc.

Also looks wise, did the GTS-4 look like the GTR? pumped guards etc.

What are the common problems in both these cars also...

Im new to the skyline and ive just sold my RS liberty, so im keen on getting some background on both these cars, and maybe buying the one that suits me best.

Thanks for your patience.

BC

Link to comment
Share on other sites
smok74 Community Regular

smok74

Posted
Posted

Just my 1/2 cent worth, does anyone remember the blue RB26DETT R32 that they built in HIGH OCTANE 3 & 4, well, it was a R32 GTS4 they picked up from the car yard, but when they dynoed it, it was dynoed at only the rear wheels ( I remember seeing the front wheels being stationary on the dyno ) ......so whats the go there? Been wondering for a while about that.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • klutched
      GOT SUM's RB34

      By klutched · Posted

      Got some decent progress after work yesterday and also today. Got the ECU all wired and passenger side interior all back together. Kept the wiring up nice and high to avoid people standing on it. Got the surge tank relays rewired and tidied up the pump wiring and cut a hole to bring the cables through.  I found a spare USB cable I had lying around so I decided to cut it up and see if I could use it for my CAN 1 bus. Turned out one of the pins I needed was to the shield of the cable so i cut it up and desoldered it and resoldered to the correct pins.  Had the issue with the powersteering hose hitting the A/C compressor and fan shroud. I pulled the bracket off and modified it to remove the front mounting point which now clears it all. Will keep an eye on it to see if theres any signs of fouling once it's up and running.
    • hardsteppa
      R32 OEM rims name?

      By hardsteppa · Posted

      That's some good input mate. Nice.
    • PranK
      My BMW 335i

      By PranK · Posted

      So today I went well outside my comfort zone (again) to replace my valve cover gasket.  I have had a big leak over the exhaust leading to a lot of smoke and smell every time I drove it. The leak was in the rear driver's corner.  The job wasn't hard as such, just a bit finicky and time consuming.  The old gasket was rock hard and broken right where the leak was.  The leaky corner had so much sitting oil in it.  The good news to my amateur eyes was no buildup or sludge under the cover. It all looked fairly nice in there.   I haven't started it yet. I ran out of light and body when putting the coils and injector loom back in. Probs only 30min left for the morning.  I was so nervous putting the cover back on, I must have lifted it 5 times to make sure the gasket was still seated properly. God it's going to be nice to be leak free and not make other traffic light queuers think my car is about to explode.
    • The Bogan
      MLR's Bogan cruise ship

      By The Bogan · Posted

      Gave the Mazda it's first wash, it will need some clay, a light compound, and polish polish to remove a few swirl marks, but that will be a job for when I have a full day to get my DA polisher action on
    • Jonesy93
      R32 vs R33 R34 C34 heater core matrix and elbow pipes info thread

      By Jonesy93 · Posted

      Just did this job on my 32 with the boost doc kit. was quite simple to fit, hardest part was getting the rubber bungs back on the firewall. does anyone know how the heater will work now without the flap in the bend? Will I just have a heater on 24/7 now?
×
×
  • Create New...