Jump to content
SAU Community

Need a glazier... anyone but Obriens

THE CHIEF

By THE CHIEF,
in Victoria

 Share

Recommended Posts

predator Grand Master

predator

Posted
Posted

u could try the join in baysie i went to a couple of years back for the 31 .. prolly still there. They had great prices on the window, they can prolly get the seals too..

just near the railway tracks along scoresby rd..

doxximus Grand Master

doxximus

Posted
Posted

you could give Custom Cut a try. dunno prices really but we do a lot of general glass trade with them, they do a lot of car windows etc as well.

otherwise just listen to what that queenslander has to say :( that might be closer to you as well (or custom cut might not come out that far? i dunno)

hope your car wasnt out last night :rofl:

Mavric Grand Master

Mavric

Posted
Posted

Hey dude i would give a joint called "Roy's Windscreens" a call hes a top bloke did an awsome job of fixing mine when it came off..

Number: 0417323115

He's very fair and does a good job you may have seen his van around it's bright orange good luck hope he can possibly help you out.....

THE CHIEF Proficient

THE CHIEF

Posted
  • Author
Posted
y

hope your car wasnt out last night :(

It was out yesterday... and when i got to the car the drivers side floor was covered in water :rofl:

Mavric, thanks for the contact, I called Roy and he is really helpful. Gonna get him to check it out. He is going to pull everything off, do a compression test and find whats causing the leak and he told me worse case scenario will cost $66!

Much better than Obriens and their BS

Thanks

Mavric Grand Master

Mavric

Posted
Posted

no worries dude hes a top bloke tell him the dude wif the Yellow R33 reccomended u to him when he comes around he shoudl remember me lol my car aint one u would forget...

take it easy hope he works it all out for you...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • drifter17a
      R34 gtt rb25det neo timing belt kit

      By drifter17a · Posted

      So been ocd with timing mark but checked from few angle and seems both cam are on and crank is matching as well to the slot on sump and crank pully   i noticed crankshaft cover has been robbed as per attached pic. Any ideas why? Could my balancer or harmonic be on its way out? should I replace the cover? https://ibb.co/ZR1JFYRR
    • drifter17a
      R34 gtt rb25det neo timing belt kit

      By drifter17a · Posted

      So now doing the change and first time dealing with rb so little nervous giving engine power and potential for screwing it up When you align all marks and then remove crank bolt, timing move little I assume you can put the bolt back in once you have removed the pully to get timing to where you want?   here is pic of my both intake and exchust cam aligned, depending on angle you look they seem to be either aligned or a half tooth or so out. Any thoughts? Should you angle your face and look at each mark that way as if looking straight rather than from above as it can be misleading   <a href="https://ibb.co/ZpnhcvbF"><img src="https://i.ibb.co/HfWrGR9b/IMG-4447.jpg" alt="IMG-4447" border="0"></a> <a href="https://ibb.co/4wm2wn4q"><img src="https://i.ibb.co/JWBqWwr1/IMG-4445.jpg" alt="IMG-4445" border="0"></a>   https://ibb.co/ZpnhcvbF https://ibb.co/4wm2wn4q
    • sunsetR33
      braided lines for the turbos

      By sunsetR33 · Posted

      Thanks for the reply @GTSBoy Haven't really thought of that yet, but you are right. If the hose was damaged it should be absolutely pissing by now. I'll put some heat sleeve around it for good measure since I'm already removing the line anyway.  Maybe I'll put on some of the stock hardlines if I ever fully remove the turbos again. Maybe when T51R modding the compressor housings? Might be a fun mod on GT28s for that "fake single turbo" effect.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 1: I did some work on the car already before finalizing this post and my "issues" list. I dropped the Tomei exhaust in favor of the HKS Hi Power Silent. Sounds nice and I can actually hear myself think now. Also gives me a realistic chance to legally drive without silencer inserts. A bit of cheating was necessary to still be able to mount the Top Secret style diffuser. Some malusage of washers and a bit of "convincing" toward the brackets and exhaust hanger seemed to do the trick. The shaky steering wheel has been resolved as various suspension components were worn, like sway bar bushings and link bars. Most notably the two steering tie rod ends. Had some trouble finding bushings because my sway bars are not OEM thickness, 23.x up front and 27 rear. But non adjustable, so no aftermarket I suppose. Maybe they are nismo units? Turbo oil drain hoses were definitely still the originals and are new now. Wasn't the cause of the turbo oil leak sadly. Currently removing the rear turbo because of it, I suspect the braided oil feed line is the culprit. This issue needs to be dealt with so I can work towards actually getting the turbo setup legal and inspected. Two new issues to add to the list as well. Rear Main seal is probably leaking. Time will show how bad it is, I don't really want to drop the gearbox right now just for the stupid seal. Could fix a few other things in one go once I do that. Front right driveshaft grease is going past the cv boot, so at some point I'll fix that too.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Ok so no 4cyl clutch... Yeah it is a factory manual. So if iam correct i need clutch and flywheel too? I can use something that suits something like R32 GTST?   EDIT: https://www.ebay.com/itm/224291042776 Is this ok?   EDIT2: i maybe forget to mention this(dk how important it is) but the trans will be behind RB25DET NEO(iam doing swap) It will be there for a little while. Iam planing to do bigbox or BMW tranny..
×
×
  • Create New...