Jump to content
SAU Community

Recommended Posts

drifting doesnt need mods, the more mods the easyer it becomes to drift (my thread anywayz) for example to get a stocky r33 sideways (yes it is very possable and not just power-side) it is abit hard due to weight etc etc but if it had like a 400ps and a few sups mods i belived it would be soo much easyer.

drifting is more skill than anything i belived, if in the d1 a 175ps ae86 can out drift a 450ps s15, and a r34 4dr, soarer and chaser which all weight alot can also drift and place in the 10top what can i say.

ohh yeah turn wheels in slightly = camber

what does camber mean ?

and what about sway bars ? are they needed? i always thought the body would start to bend n stuff after lots of drifting without these bars, or am i wrong?

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

what does camber mean ?

and what about sway bars ? are they needed? i always thought the body would start to bend n stuff after lots of drifting without these bars, or am i wrong?

Static camber (as in camber while stationary) is the angle of the wheel to the ground. For example zero camber gives complete and even contact of the tyre with the ground so that it isn't biased on any particular side of the tyre and hence gives more traction.

People often talk up about negative camber so that it compensates for the turning forces in the car so that under heavy turning the car can be as close to zero camber as possible. Too much negative camber however and it will eat away at your tyres quicker than you can say F***, this is why most modded street cars go for about negative 1 degree of camber and race cars go for about negative 2-3 degrees.

Sway bars bars also known as anti-roll bars help the weight transition when cornering. If the bars didnt exist, if you turned really quickly all the weight of the car would move very quickly to one particular side of the car. Upgrading sway bars makes the car much stiffer and puts more even loads on both sides of the car during fast cornering. Also the particular stiffness can affect whether the car understeers or oversteers by nature. This is dependant on the different stiffness of the rear and front sway bars.

:P

Static camber (as in camber while stationary) is the angle of the wheel to the ground. For example zero camber gives complete and even contact of the tyre with the ground so that it isn't biased on any particular side of the tyre and hence gives more traction.

People often talk up about negative camber so that it compensates for the turning forces in the car so that under heavy turning the car can be as close to zero camber as possible. Too much negative camber however and it will eat away at your tyres quicker than you can say F***, this is why most modded street cars go for about negative 1 degree of camber and race cars go for about negative 2-3 degrees.

Sway bars bars also known as anti-roll bars help the weight transition when cornering. If the bars didnt exist, if you turned really quickly all the weight of the car would move very quickly to one particular side of the car. Upgrading sway bars makes the car much stiffer and puts more even loads on both sides of the car during fast cornering. Also the particular stiffness can affect whether the car understeers or oversteers by nature. This is dependant on the different stiffness of the rear and front sway bars.  

:P

Wow nice answer man, so in other words get sway bars for better corning because the weight is distributed evenly ?

So the sway bars dont protect your car body from bendin? is it even possible for a car body to start bending or something after tonnes of drifting ? like say over a couple years of drifting every now n then.

The car will probably start bending after time but I imagine (not quite 100%) the sway bar would bend before any other damage would be done. A stiffer sway means that when a car is cornering, more force is distributed onto the inside wheel rather than dumping it all on the outside tyre. I imagine that having stiffer sway bars elimanates the need for going out and spending heaps on really stiff drift coilovers to get basically the same result. That way the body wont flex as much and softer springs can be used for day to day driving. However if you avoid using coilovers completely you start to worry about centre of gravity etc. etc.

  • 2 weeks later...

well as for the next events, have a looksie here...

C-Red are organising a barbagallo day..

http://www.driveline.net.au/news.php?news_id=36

Tenagah motorsports are also organising a day in april down at collie.

Details on that event can be found here http://www.driveline.net.au/eventDetails.p...hp?event_id=177

c-red is aimed at mainly pro's. its only for 3 hours on a friday night so they dont wanna have to stop all the time to dig pplz out of the sand. which is fair enough.

collie would be the good idea :P

there are lots of places to street drift.. but it shouldnt be done... unless u like to bend over and take it whilst u see ur car leave on a trailer :)

-pie

well the training day is april.. so by then it will be fine.. not sure if anything will be planned sooner.

and AHG is out for drift... they do hold MC days there on the skid pans but thats about all..

-pie

Hell yeah, someone should make one on a property out of the metro. I would be going there all the time. Well when you think about it. Theres basically nowhere you can take your car to go drifting (legally) or to go and do burnouts other than the drags and the occassional drift meeting at some tracks. I would be spending a bit of time there.

drifting doesnt need mods, the more mods the easyer it becomes to drift (my thread anywayz) for example to get a stocky r33 sideways (yes it is very possable and not just power-side) it is abit hard due to weight etc etc but if it had like a 400ps and a few sups mods i belived it would be soo much easyer.

drifting is more skill than anything i belived, if in the d1 a 175ps ae86 can out drift a 450ps s15, and a r34 4dr, soarer and chaser which all weight alot can also drift and place in the 10top what can i say.

ohh yeah turn wheels in slightly = camber

and use Khumo tyres, don't need much else

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
    • OK, if it idles at 1000+ with the AAC, its not an idle airflow problem. The cold start valve just gives extra air when the engine is cold, but you have enough air without it to idle at 1000. I think you are back to a fuel problem, sorry. Can you see the fuel pressure staying constant or does it drop as the revs drop to a stall?  
×
×
  • Create New...