Jump to content
SAU Community

Recommended Posts

drifting doesnt need mods, the more mods the easyer it becomes to drift (my thread anywayz) for example to get a stocky r33 sideways (yes it is very possable and not just power-side) it is abit hard due to weight etc etc but if it had like a 400ps and a few sups mods i belived it would be soo much easyer.

drifting is more skill than anything i belived, if in the d1 a 175ps ae86 can out drift a 450ps s15, and a r34 4dr, soarer and chaser which all weight alot can also drift and place in the 10top what can i say.

ohh yeah turn wheels in slightly = camber

what does camber mean ?

and what about sway bars ? are they needed? i always thought the body would start to bend n stuff after lots of drifting without these bars, or am i wrong?

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

what does camber mean ?

and what about sway bars ? are they needed? i always thought the body would start to bend n stuff after lots of drifting without these bars, or am i wrong?

Static camber (as in camber while stationary) is the angle of the wheel to the ground. For example zero camber gives complete and even contact of the tyre with the ground so that it isn't biased on any particular side of the tyre and hence gives more traction.

People often talk up about negative camber so that it compensates for the turning forces in the car so that under heavy turning the car can be as close to zero camber as possible. Too much negative camber however and it will eat away at your tyres quicker than you can say F***, this is why most modded street cars go for about negative 1 degree of camber and race cars go for about negative 2-3 degrees.

Sway bars bars also known as anti-roll bars help the weight transition when cornering. If the bars didnt exist, if you turned really quickly all the weight of the car would move very quickly to one particular side of the car. Upgrading sway bars makes the car much stiffer and puts more even loads on both sides of the car during fast cornering. Also the particular stiffness can affect whether the car understeers or oversteers by nature. This is dependant on the different stiffness of the rear and front sway bars.

:P

Static camber (as in camber while stationary) is the angle of the wheel to the ground. For example zero camber gives complete and even contact of the tyre with the ground so that it isn't biased on any particular side of the tyre and hence gives more traction.

People often talk up about negative camber so that it compensates for the turning forces in the car so that under heavy turning the car can be as close to zero camber as possible. Too much negative camber however and it will eat away at your tyres quicker than you can say F***, this is why most modded street cars go for about negative 1 degree of camber and race cars go for about negative 2-3 degrees.

Sway bars bars also known as anti-roll bars help the weight transition when cornering. If the bars didnt exist, if you turned really quickly all the weight of the car would move very quickly to one particular side of the car. Upgrading sway bars makes the car much stiffer and puts more even loads on both sides of the car during fast cornering. Also the particular stiffness can affect whether the car understeers or oversteers by nature. This is dependant on the different stiffness of the rear and front sway bars.  

:P

Wow nice answer man, so in other words get sway bars for better corning because the weight is distributed evenly ?

So the sway bars dont protect your car body from bendin? is it even possible for a car body to start bending or something after tonnes of drifting ? like say over a couple years of drifting every now n then.

The car will probably start bending after time but I imagine (not quite 100%) the sway bar would bend before any other damage would be done. A stiffer sway means that when a car is cornering, more force is distributed onto the inside wheel rather than dumping it all on the outside tyre. I imagine that having stiffer sway bars elimanates the need for going out and spending heaps on really stiff drift coilovers to get basically the same result. That way the body wont flex as much and softer springs can be used for day to day driving. However if you avoid using coilovers completely you start to worry about centre of gravity etc. etc.

  • 2 weeks later...

well as for the next events, have a looksie here...

C-Red are organising a barbagallo day..

http://www.driveline.net.au/news.php?news_id=36

Tenagah motorsports are also organising a day in april down at collie.

Details on that event can be found here http://www.driveline.net.au/eventDetails.p...hp?event_id=177

c-red is aimed at mainly pro's. its only for 3 hours on a friday night so they dont wanna have to stop all the time to dig pplz out of the sand. which is fair enough.

collie would be the good idea :P

there are lots of places to street drift.. but it shouldnt be done... unless u like to bend over and take it whilst u see ur car leave on a trailer :)

-pie

well the training day is april.. so by then it will be fine.. not sure if anything will be planned sooner.

and AHG is out for drift... they do hold MC days there on the skid pans but thats about all..

-pie

Hell yeah, someone should make one on a property out of the metro. I would be going there all the time. Well when you think about it. Theres basically nowhere you can take your car to go drifting (legally) or to go and do burnouts other than the drags and the occassional drift meeting at some tracks. I would be spending a bit of time there.

drifting doesnt need mods, the more mods the easyer it becomes to drift (my thread anywayz) for example to get a stocky r33 sideways (yes it is very possable and not just power-side) it is abit hard due to weight etc etc but if it had like a 400ps and a few sups mods i belived it would be soo much easyer.

drifting is more skill than anything i belived, if in the d1 a 175ps ae86 can out drift a 450ps s15, and a r34 4dr, soarer and chaser which all weight alot can also drift and place in the 10top what can i say.

ohh yeah turn wheels in slightly = camber

and use Khumo tyres, don't need much else

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...