Jump to content
SAU Community

HICAS~help

Crossie

By Crossie,
in General Maintenance

 Share

Recommended Posts

  • 2 weeks later...
The Dan Grand Master

The Dan

Posted
Posted

Check to see the the motor is plugged in. It is located closer to the rear of the vehicle on the driver's side. It has Sumitomo on it (manufacturers).

Some people disconnect it to avoid problems or to solve problems they are having.

Link to comment
https://www.sau.com.au/forums/topic/63569-hicas~help/#findComment-1213232
Share on other sites
z00mxr32 Contributor

z00mxr32

Posted
Posted
Check to see the the motor is plugged in. It is located closer to the rear of the vehicle on the driver's side. It has Sumitomo on it (manufacturers).  

 

Some people disconnect it to avoid problems or to solve problems they are having.

the unit is still there but it looks like it has been altered.. it has a small TOMEI black unit piggy-backed on the hicas unit.

what does this mean??

better or worse?

suspension has been changed to a full trust suspension and bushes the rod holing the bushes...and also a cusco tower brace with another brace that is holding the brake master cylinder.

what does this all mean??? that the car was used for circuit? / drag/ drift?

someone help .. thanks!

Link to comment
https://www.sau.com.au/forums/topic/63569-hicas~help/#findComment-1217213
Share on other sites
The Dan Grand Master

The Dan

Posted
Posted

It is possible that it has been but you could never be sure.

That is a TOMEI hicas locking kit. It locks the Hicas in place. Usually good for better drifting, I wouldn't disconnect the Hicas for circuit though.

Sounds like it's had quite a bit of work done.

Link to comment
https://www.sau.com.au/forums/topic/63569-hicas~help/#findComment-1217512
Share on other sites
MerlinTheHapyPig Mentor

MerlinTheHapyPig

Posted
Posted

it's probably got a hicas lock kit, however the tomei plug-in thing should stop the warning light from coming on.

Alot of people also get the warning light come on when they have an aftermarket steering wheel.

leave it as-is, most people prefer hicas turned off coz it makes the car's handling a lot more predictable (but also less idiot proof)

Link to comment
https://www.sau.com.au/forums/topic/63569-hicas~help/#findComment-1218012
Share on other sites
z00mxr32 Contributor

z00mxr32

Posted
Posted

yeh it does say TOMEI hicas locking unit.

so i shouldnt have a problem driving around sharp turns an shiet ..?

no wonder the car handles really good ... specially at take off ..the back doesnt even sag down when on full boost then change to 2nd all u hear is a small squek and continues..

thanks guys ..

Link to comment
https://www.sau.com.au/forums/topic/63569-hicas~help/#findComment-1218380
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • GTSBoy
      Freddy Plenum vs Genuine options RB25

      By GTSBoy · Posted

      My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • Murray_Calavera
      R33 persistent issues. P/steering and lag/misfire

      By Murray_Calavera · Posted

      There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...