Jump to content
SAU Community

Recommended Posts

Well i got my GTR fuel pump yesterday after everyone said its a direct swap only to find its bigger in every way and is not a direct fit. Took me a while but after some modifying i now have a GTR pump in my 32 GTS-T. Now did i do something wrong or is some modifying required to put it in?

Link to comment
https://www.sau.com.au/forums/topic/63615-gtr-pump-direct-fit-ye-right/
Share on other sites

Depends on the pump. i fitted a BNR32 pump to an ECR33 & there was some minor d!cking around involved, using hose clamps/nitrile rubber sheet & swapping the pickups between the two.

Had I fitted a BCNR33 pump would have been a straight swap. :D

Well i got my GTR fuel pump yesterday after everyone said its a direct swap only to find its bigger in every way and is not a direct fit. Took me a while but after some modifying i now have a GTR pump in my 32 GTS-T. Now did i do something wrong or is some modifying required to put it in?

i put a r33 gtr pump in my r32, it wasnt as easy as i thought....i used the rubber that goes at the bottom of the put and put it between the pump and the bracket and then zip tied it in 4 spots and it almost sounds like the stock one still(doesnt vibrate).

I had to cut the metal hose down abit so i could move the pump upwards.

I then used a spare new EA ford falcon filter sock i had lying around she was good as gold.....

i had to adjust it abit because the first time i put it in, it was touching the bottom of the tank.

So maybe i'm just bodgy! :D

i put a r33 gtr pump in my r32, it wasnt as easy as i thought....i used the rubber that goes at the bottom of the put and put it between the pump and the bracket and then zip tied it in 4 spots and it almost sounds like the stock one still(doesnt vibrate).  

I had to cut the metal hose down abit so i could move the pump upwards.

I then used a spare new EA ford falcon filter sock i had lying around she was good as gold.....

i had to adjust it abit because the first time i put it in, it was touching the bottom of the tank.

So maybe i'm just bodgy!  :D

thats almost exactly what i did but i didn't replace to sock and used hose clamps instead of zip ties, only makes a little more noise than standard!

I got some form of GTR pump in my gtst (r33) and it vibrates a lot. although when I cruise past people may think I'm running a serious drag racing fuel setup or something in the boot ;)

I think it came from a r32, but I didnt fit it :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...