Jump to content
SAU Community

Recommended Posts

On 20/05/2025 at 9:57 PM, silviaz said:

If I do a spot repair and I put filler in a dent for example and sand outside of the repair with 320 grit lets say so the primer can stick as I will only put primer on that repair and the surrounding area and then repaint the whole panel.

Sounds good. 

On 20/05/2025 at 9:57 PM, silviaz said:

Don't I need to make sure that I don't put primer on the old clear coat? I keep seeing YouTube videos where people have new paint and primer land on the old clearcoat that isn't even dulled down, it's still shiny. I thought putting paint on clearcoat or primer on clearcoat is a bad idea because it won't stick.

I don't 100% understand what your getting at here. When you say, "I keep seeing YouTube videos where people have new paint and primer land on the old clearcoat that isn't even dulled down" do you mean this - there is a panel with factory paint, without any prep work, they paint the entire panel with primer, then colour then clear? 

If that's what you mean, sure it will "stick" for a year, 2 years, maybe 3 years? Who knows. But at some stage it will flake off and when it does it's going to come off in huge chunks and look horrific. 

On 20/05/2025 at 9:57 PM, silviaz said:

Don't I need to make sure that I don't put primer on the old clear coat?

Of course read your technical data sheet for your paint, but generally speaking, you can apply primer to a scuffed/prepped clear coat. Generally speaking, I wouldn't do this. I would scuff/prep the clear and then lay colour then clear. Adding the primer to these steps just adds cost and time.

On 20/05/2025 at 9:57 PM, silviaz said:

I thought putting paint on clearcoat or primer on clearcoat is a bad idea because it won't stick.

It will stick to the clear coat provided it has been appropriately scuffed/prepped first. 

On 20/05/2025 at 9:57 PM, silviaz said:

So in this scenario it's a bit different to mine but imagine someone doing a spot repair and only painting that small section of repair but the new paint is landing on the old clearcoat.

When you say, "but the new paint is landing on the old clearcoat" I am imagining someone not masking up the car and just letting overspray go wherever it wants. Surely this isn't what you mean? 

So I'll assume the following scenario - there is a small scratch. The person manages to somehow fill the scratch and now has a perfectly flat surface. They then spray colour and clear over this small masked off section of the car. Is this what you mean? If this is the case, yes the new paint will eventually flake off in X number of years time. 

The easy solution is to scuff/prep all of the paint that hasn't been masked off in the repair area then lay the paint. 

1 hour ago, silviaz said:

Bit of a similar question, apprently with epoxy primer you can just sand the panel to 240 grit then apply it and put body filler on top.

So you want to prep the surface, lay primer, then lay filler, then lay primer, then colour, then clear? 

Life seems so much simpler if you prep, fill, primer, colour then clear. 

1 hour ago, silviaz said:

So does that basically mean you almost never have to go to bare metal for simple dents?

There are very few reasons to go to bare metal. Chasing rust is a good example of why you'd go to bare metal. 

A simple dent, there is no way in hell I'm going to bare metal for that repair. I've got enough on my plate without creating extra work for myself lol. 

  • Like 1
Posted (edited)
16 hours ago, Murray_Calavera said:

Sounds good. 

I don't 100% understand what your getting at here. When you say, "I keep seeing YouTube videos where people have new paint and primer land on the old clearcoat that isn't even dulled down" do you mean this - there is a panel with factory paint, without any prep work, they paint the entire panel with primer, then colour then clear? 

If that's what you mean, sure it will "stick" for a year, 2 years, maybe 3 years? Who knows. But at some stage it will flake off and when it does it's going to come off in huge chunks and look horrific. 

Of course read your technical data sheet for your paint, but generally speaking, you can apply primer to a scuffed/prepped clear coat. Generally speaking, I wouldn't do this. I would scuff/prep the clear and then lay colour then clear. Adding the primer to these steps just adds cost and time.

It will stick to the clear coat provided it has been appropriately scuffed/prepped first. 

When you say, "but the new paint is landing on the old clearcoat" I am imagining someone not masking up the car and just letting overspray go wherever it wants. Surely this isn't what you mean? 

So I'll assume the following scenario - there is a small scratch. The person manages to somehow fill the scratch and now has a perfectly flat surface. They then spray colour and clear over this small masked off section of the car. Is this what you mean? If this is the case, yes the new paint will eventually flake off in X number of years time. 

The easy solution is to scuff/prep all of the paint that hasn't been masked off in the repair area then lay the paint. 

So you want to prep the surface, lay primer, then lay filler, then lay primer, then colour, then clear? 

Life seems so much simpler if you prep, fill, primer, colour then clear. 

There are very few reasons to go to bare metal. Chasing rust is a good example of why you'd go to bare metal. 

A simple dent, there is no way in hell I'm going to bare metal for that repair. I've got enough on my plate without creating extra work for myself lol. 

Thanks for all that information I appreciate it. To answer your questions:

- Yep that's what I mean. These guys are professional painters to so I must be missing something. It's a bit hard to explain.

- With the primer landing on clearcoat, I make sure that the surrounding clearcoat is scuffed to 240 grit as my epoxy primer says that I only need to sand the area to 240 grit.

- Yeah so similar to the first question, assuming that the paint landed on the unscuffed clearcoat because I've seen that happen.

- Yep I want to prep the surface in that order. Only reason because epoxy primer will protect it from rust and I need that atm with this crappy Sydney weather. I think I was worried about time, if I try to put the filler down but screw it up somehow and I don't have time to sand it off and reapply it then need to put primer later that it might start to rust again so I wanted to apply the primer as quick as possible to not deal with rust. 

- I just deleted some answers, I just realised after watching a video and what you said about looking at the data sheet, that I need to read the data sheet on the specific filler I'm using. It's possible now that I put epoxy primer first was a waste of time and need to go to bare metal lol

Edited by silviaz
1 hour ago, silviaz said:

- Yep that's what I mean. These guys are professional painters to so I must be missing something. It's a bit hard to explain.

Post up the youtube video your referring to, will be much easier then us playing charades together lol. 

1 hour ago, silviaz said:

- Yeah so similar to the first question, assuming that the paint landed on the unscuffed clearcoat because I've seen that happen.

Lets see the videos in question. 

1 hour ago, silviaz said:

Only reason because epoxy primer will protect it from rust and I need that atm with this crappy Sydney weather

If the car is in your garage and you sand it back to bare metal, you'd be surprised how much time you have to work with before it starts to rust. As long as you're actively working on the car in your free time, you're going to be fine. 

1 hour ago, silviaz said:

I need to read the data sheet on the specific filler I'm using

I assume everyone is reading the data sheets for all the materials they are using before using them. If you're not, please start doing this lol. 

  • Like 1
2 minutes ago, Murray_Calavera said:

Post up the youtube video your referring to, will be much easier then us playing charades together lol. 

Lets see the videos in question. 

If the car is in your garage and you sand it back to bare metal, you'd be surprised how much time you have to work with before it starts to rust. As long as you're actively working on the car in your free time, you're going to be fine. 

I assume everyone is reading the data sheets for all the materials they are using before using them. If you're not, please start doing this lol. 

Yep I'll find those and get back to you. To be honest I wasn't aware of data sheets until you mentioned it. I'm still new to this haha, lots to learn. My car is parked outside, it rusted in less than 24 hours lol. Only minor surface rust that was easily removed but I've been worried that it might rust from the inside out and screw me over in the long term (if I decide to keep the shitbox for that long).

24 minutes ago, Murray_Calavera said:

Post up the youtube video your referring to, will be much easier then us playing charades together lol. 

Lets see the videos in question. 

If the car is in your garage and you sand it back to bare metal, you'd be surprised how much time you have to work with before it starts to rust. As long as you're actively working on the car in your free time, you're going to be fine. 

I assume everyone is reading the data sheets for all the materials they are using before using them. If you're not, please start doing this lol. 

Ok I FINALLY found a video lol. This took way longer than it should have as I could have sworn I saw multiple videos like this. I kept finding the completely opposite (the correct way of doing this). I wouldn't be surprised if I f**ked this up somehow. 

I just realised where I've been getting confused and even with other things I work on. I haven't been doing things the regular way instead I'm going a roundabout way of doing things, like putting epoxy primer first then filler for example instead of putting just filler then primer on top of that, then wondering what happens if I get that primer on the clear coat that I haven't sanded yet. This was a bit of an epiphany 😂 

But anyways, here this video. Time stamp, 2:56, some of the primer lands on the paint unscuffed above. You can see from the reflection it looks shiny.

 

@silviaz

Ok cool, so much easier with a video. I can see why this video would be confusing for new players.  

It is obvious that this entire bonnet is going to be resprayed, have a look in the background around 2:05, you can see a bunch of bare metal on the left side of the bonnet. 

It's not an issue for the primer being laid down on the non-prepped clear on the bonnet. It will be sanded off at a later stage. 

This might not be obvious to new players, but working on bare metal and factory paint in this instance, the factory paint is like a mountain and the bare metal is a huge valley. The bonnet needs to be levelled flat before it receives it's final stage of colour and clear coat. During this levelling process, the primer that is landing on the clear that you are worried about will be removed. 

Also, this guy is out of control. Zero PPE while spraying, maybe he is a good example overall about what not to do lol.

  • Like 1
Posted (edited)
3 hours ago, Murray_Calavera said:

@silviaz

Ok cool, so much easier with a video. I can see why this video would be confusing for new players.  

It is obvious that this entire bonnet is going to be resprayed, have a look in the background around 2:05, you can see a bunch of bare metal on the left side of the bonnet. 

It's not an issue for the primer being laid down on the non-prepped clear on the bonnet. It will be sanded off at a later stage. 

This might not be obvious to new players, but working on bare metal and factory paint in this instance, the factory paint is like a mountain and the bare metal is a huge valley. The bonnet needs to be levelled flat before it receives it's final stage of colour and clear coat. During this levelling process, the primer that is landing on the clear that you are worried about will be removed. 

Also, this guy is out of control. Zero PPE while spraying, maybe he is a good example overall about what not to do lol.

Ah ok makes sense, thanks for that clarification it helps a lot. My PPE was terrible recently, I sprayed a can of primer on a panel and the wind blew and I didn't have safety goggles and the mist went in my eye. Didn't take the wind into account, good lesson learned though lol.

 

I guess if I want to be extra careful I can always scuff the whole panel before putting primer like the other videos are doing.

Edited by silviaz
Posted (edited)
3 hours ago, Murray_Calavera said:

@silviaz

Ok cool, so much easier with a video. I can see why this video would be confusing for new players.  

It is obvious that this entire bonnet is going to be resprayed, have a look in the background around 2:05, you can see a bunch of bare metal on the left side of the bonnet. 

It's not an issue for the primer being laid down on the non-prepped clear on the bonnet. It will be sanded off at a later stage. 

This might not be obvious to new players, but working on bare metal and factory paint in this instance, the factory paint is like a mountain and the bare metal is a huge valley. The bonnet needs to be levelled flat before it receives it's final stage of colour and clear coat. During this levelling process, the primer that is landing on the clear that you are worried about will be removed. 

Also, this guy is out of control. Zero PPE while spraying, maybe he is a good example overall about what not to do lol.

A question. So I've attached some images, the red circled ones are where I put 2-3 coats of epoxy primer to protect it from rust. For the purpose of this example let's pretend I won't put body filler there because it's straight and will put 2k primer 3 coats after it's all done. And the last image the paint looks terrible because my paint/clearcoat was all blistered but the scratches are completely smooth and sanded down (I also plan to prime this entire panel) 

My question is

- If I put 2k primer over all those repairs that you see from all 3 images, do I need to sand it because it might show in the paint or should it be fine as it's all smooth and sanded down? 

image.png

image.png

image.png

Edited by silviaz
1 minute ago, silviaz said:

Ah ok makes sense, thanks for that clarification it helps a lot. My PPE was terrible recently, I sprayed a can of primer on a panel and the wind blew and I didn't have safety goggles and the mist went in my eye. Didn't take the wind into account, good lesson learned though lol.

After reading this I think this is really important to mention - please for the love of god do not spray any 2 pack paint (typically advertised as 2K, it contains a hardener that is mixed before spraying) without a proper respirator, gloves, eye protection and preferably a full one piece disposable paint suit. That stuff is nasty and can really f*ck you up. 

Also worth mentioning, the filters on the respirator will require changing before you can smell the chemicals through them. 

So with a brand new respirator and filters, you shouldn't smell anything at all when spraying. If you later can smell the paint chemicals, you've changed your filters too late. 

Filters are cheap, replace them often.

  • Like 1
Posted (edited)
1 minute ago, Murray_Calavera said:

After reading this I think this is really important to mention - please for the love of god do not spray any 2 pack paint (typically advertised as 2K, it contains a hardener that is mixed before spraying) without a proper respirator, gloves, eye protection and preferably a full one piece disposable paint suit. That stuff is nasty and can really f*ck you up. 

Also worth mentioning, the filters on the respirator will require changing before you can smell the chemicals through them. 

So with a brand new respirator and filters, you shouldn't smell anything at all when spraying. If you later can smell the paint chemicals, you've changed your filters too late. 

Filters are cheap, replace them often.

Yeah definitely won't. I just thought because this was a quick job, I didn't need more gear even my mask wasn't a proper one but going forward I will use the proper gear. Cheers for that additional info.

Edited by silviaz
43 minutes ago, silviaz said:

- If I put 2k primer over all those repairs that you see from all 3 images, do I need to sand it because it might show in the paint or should it be fine as it's all smooth and sanded down? 

Prior to laying down the primer, you need to make sure the surface is completely level. For example, based on this picture, I strongly suspect that the areas marked in blue are higher then the area marked in green. image.thumb.png.33e02e0a8e5e87aa75c038529f04bf5b.png

If you spray primer over this entire area, then paint and clear it, the finished result will 100% show the low area. It will stick out like dogs balls. Unfortunately the paint won't magically level out the low areas as you lay it down. 

Without seeing it in person, I expect that the green area will need to be filled, then use a guide coat and check that the entire repair area is level with a large sanding block. 

image.thumb.png.e3064d2804c1316cf7d748a197fef575.png

With this picture, are you saying that even though you can see the scratches, the panel is in fact completely smooth and flat? If this is the case sure you could prep and paint it as it is.  

 

The picture with the paint you described as blistering, it's hard for me to comment on from the photo alone. It looks like the panel is wet? Dunno, looks strange. Does the panel feel as smooth as glass when you run your hand over it?

****

Going back to your question again, generally you would only sand the primer if you made a mistake while laying down the primer. 

If the panel is prepped properly and you lay the primer down properly, you should not need to sand the primer. 

This wouldn't work - Don't prep the panel. Spray primer and see how it turns out. Sand the areas where the issues appear. Spray more primer and see how it turns out. Sand the areas....... Yeah you'd go round and round in circles getting no where. 

  • Thanks 1
5 minutes ago, Murray_Calavera said:

Prior to laying down the primer, you need to make sure the surface is completely level. For example, based on this picture, I strongly suspect that the areas marked in blue are higher then the area marked in green. image.thumb.png.33e02e0a8e5e87aa75c038529f04bf5b.png

If you spray primer over this entire area, then paint and clear it, the finished result will 100% show the low area. It will stick out like dogs balls. Unfortunately the paint won't magically level out the low areas as you lay it down. 

Without seeing it in person, I expect that the green area will need to be filled, then use a guide coat and check that the entire repair area is level with a large sanding block. 

image.thumb.png.e3064d2804c1316cf7d748a197fef575.png

With this picture, are you saying that even though you can see the scratches, the panel is in fact completely smooth and flat? If this is the case sure you could prep and paint it as it is.  

 

The picture with the paint you described as blistering, it's hard for me to comment on from the photo alone. It looks like the panel is wet? Dunno, looks strange. Does the panel feel as smooth as glass when you run your hand over it?

****

Going back to your question again, generally you would only sand the primer if you made a mistake while laying down the primer. 

If the panel is prepped properly and you lay the primer down properly, you should not need to sand the primer. 

This wouldn't work - Don't prep the panel. Spray primer and see how it turns out. Sand the areas where the issues appear. Spray more primer and see how it turns out. Sand the areas....... Yeah you'd go round and round in circles getting no where. 

Yep I will use a guide coat after putting filler, I will do it on the whole panel as I'm a beginner so chances I've made quite a few errors. In that photo, I think that was a low spot, I just for example said to pretend it's flat but I will put filler + guide coat after to assess where I'm at.

Yep with that picture, the panel is wet as it rained when I took the photo. But all those scratches are completely smooth, I went over it with 240 grit and can't feel it, even with my nail digging into it.

I was legit thinking to buy a 2k can and spray primer to see how it turns out but then thought to myself it's going to be a mess doing it haha. Good mention there.

Thanks for all that info I think I know what to do next.

5 minutes ago, silviaz said:

But all those scratches are completely smooth, I went over it with 240 grit and can't feel it, even with my nail digging into it.

Sounds good. Provided the panel is flat/level I'd be happy to start the painting process. 

6 minutes ago, silviaz said:

I was legit thinking to buy a 2k can and spray primer to see how it turns out but then thought to myself it's going to be a mess doing it haha. Good mention there.

While you are learning, for sure you could do this. Its only paint, you can always sand it all back and start again. Its only your time and money on materials, but while you're learning, really its time and money spent on your education. 

Once you know how to do this bodywork and painting, you won't want to waste your time and money on frivolous activities lol. 

  • Like 1
53 minutes ago, Murray_Calavera said:

Sounds good. Provided the panel is flat/level I'd be happy to start the painting process. 

While you are learning, for sure you could do this. Its only paint, you can always sand it all back and start again. Its only your time and money on materials, but while you're learning, really its time and money spent on your education. 

Once you know how to do this bodywork and painting, you won't want to waste your time and money on frivolous activities lol. 

Yep will do, thanks for all the help.

  • Like 1
3 hours ago, Murray_Calavera said:

Sounds good. Provided the panel is flat/level I'd be happy to start the painting process. 

While you are learning, for sure you could do this. Its only paint, you can always sand it all back and start again. Its only your time and money on materials, but while you're learning, really its time and money spent on your education. 

Once you know how to do this bodywork and painting, you won't want to waste your time and money on frivolous activities lol. 

Luckily I didn't put in etch primer as I just found out it's not compatible with my body filler lol. Also just need to sand the panel anywhere between 150-400 grit so I'm in the clear there. It does say to not apply to soft old paint, I assume that means paint that is flaking, peeling,etc

image.png

10 hours ago, silviaz said:

It does say to not apply to soft old paint, I assume that means paint that is flaking, peeling,etc

Yes correct. Also, I'd avoid applying it to soft paint (however I doubt you'll ever have to deal with it in practice). So any paint that hasn't fully hardened, could be a 1k paint that never fully hardened or it could be a 2k paint that was laid down thick and hasn't yet fully hardened. 

  • Thanks 1
Posted (edited)
8 hours ago, Murray_Calavera said:

Yes correct. Also, I'd avoid applying it to soft paint (however I doubt you'll ever have to deal with it in practice). So any paint that hasn't fully hardened, could be a 1k paint that never fully hardened or it could be a 2k paint that was laid down thick and hasn't yet fully hardened. 

Above you mentioned you only need to sand primer if there's an issue with it but with fillers it says the surface needs to be sanded to X grit beforehand. Does that sorta contradict that point as the primer hasn't been sanded yet? At the same time if I sand the primer, there's a good chance I'll expose the bare metal and I'm just chasing my tail at that point. Or I'll just use a sand sponge instead of sandpaper, it seems to be far finer in terms of abrasiveness as opposed to sandpaper.

From what I understand, filler is like primer and needs scratches from the sandpaper to help it adhere to the panel.

I realised the way I'm doing things is actually a bit counter productive as there's a chance after I put filler I will need to put epoxy primer again as opposed to putting the filler first and potentially no primer if I don't go to bare metal. Will keep this in my mind for the rest of my repairs.

Edited by silviaz
5 hours ago, silviaz said:

Above you mentioned you only need to sand primer if there's an issue with it but with fillers it says the surface needs to be sanded to X grit beforehand. Does that sorta contradict that point as the primer hasn't been sanded yet? At the same time if I sand the primer, there's a good chance I'll expose the bare metal and I'm just chasing my tail at that point. Or I'll just use a sand sponge instead of sandpaper, it seems to be far finer in terms of abrasiveness as opposed to sandpaper.

Yep, if you are applying filler it sounds like there is something wrong with the body lol. Safe to assume there is going to be a lot of sanding going on if your still applying fillers. 

Picture a perfect bare metal panel, smooth as glass. You lay down your primer, it's perfect. (why are you going to sand it?) You lay down the colour and clear, it's perfect. No sanding at all took place and you've got a perfectly finished panel. 

5 hours ago, silviaz said:

At the same time if I sand the primer, there's a good chance I'll expose the bare metal and I'm just chasing my tail at that point.

You won't be chasing your tail, sounds like you were prepping to start laying filler. If your happy with the body after the sanding, there is some bare metal exposed and some areas with primer, no issues at all, start laying the filler. You are safe to lay filler on bare metal or primer (of course check your technical data sheet as usual for what your filler is happy to adhere to). 

5 hours ago, silviaz said:

From what I understand, filler is like primer and needs scratches from the sandpaper to help it adhere to the panel.

This isn't a 100% correct statement. There is primer that is happy to adhere to smooth bare metal. There are fillers that are happy to adhere to smooth bare metal. Just make sure you're using the right materials for the job. 

5 hours ago, silviaz said:

I realised the way I'm doing things is actually a bit counter productive as there's a chance after I put filler I will need to put epoxy primer again as opposed to putting the filler first and potentially no primer if I don't go to bare metal.

Typically if you are using filler, you would go primer, colour and clear. I've never seen any instances before where someone has laid colour over body filler (maybe this happens, but I haven't seen it before). So your plan sounds pretty normal to me. 

  • Thanks 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...