Jump to content
SAU Community

Recommended Posts

  • Replies 350
  • Created
  • Last Reply

Top Posters In This Topic

Well,

I think this is all over nothing as the best time MOTOR magazine achieved for the HSV Clubsport R8 was 5.83sec 0-100 @29degC and 38% humidity.

This was performed in controlled conditions using the most aggressive driving techniques.

This is a long way short of the 5.5sec that Skylinekiller quotes as a "bad day" and as for 4.99 sec, that must of been a downhill run with a 150kmph tail wind.

Skyliner killer lost all credibility with me at that point.

Since those MOTOR boys now what there doing there might be a few more tenths better 5.83 than in cooler weather, so maybe 5.5 seconds on the best day.

Figures are in the latest PCOTY (on the shelves as of Monday) for the world to see.

haha so your agreeing that theres no point in a nissan 2.6L when you can get a mazda 1.3L

one uses a rotary one uses piston.

i can tell with the points you argue with that you have no idea.

so i lower my itelligence to your level and ask you y a holden need 5l compared to a nissan 2.6l

again, apples and oranges

you guys are absolute ****heads... **** off and die you bogan ****s...

seriously.. im sure ur car is nice.. whatever.. i like driving my skyline.. it is a great car

i hope there arnt many skylines owners that come on the LS1 forums and start talking shit

but man unless youve got something interesting to say.. like a conversion project or something just **** off...

i dont mind V8s.. i think supercharged 8s are good and the Lexus v8 range of engines are pretty cool too..

Someone **** this thread off it doesnt fo ANY of us any favors..

Your all wrong, until you have experienced Hemi 245- 2 barrel power, circa 1971 and 165hp, your all denying what real performance is:whackit: Throw it in a beautiful rust brown VF Valiant with a blue boot and your talkign the greatest race car i have ever owned...next to my 2.0L Brown Sigma:)

you were still arguing about his opinion as much as he was arguing about yours, so it makes you just as retarded. **** i laugh at internet fights, especially over cars when each party clearly has there own personal preference. surely you would realise he wont change his liking of v8's as much as you wont change your liking of skylines?

you were still arguing about his opinion as much as he was arguing about yours, so it makes you just as retarded. **** i laugh at internet fights, especially over cars when each party clearly has there own personal preference. surely you would realise he wont change his liking of v8's as much as you wont change your liking of skylines?

Well done. :)

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...