Jump to content
SAU Community

Recommended Posts

1994 Nissan Skyline R32 GTS-4

4 wheel drive, RB20DET single turbo, 5 speed manual

hybrid bar and plate front mount intercooler

3 inch turbo back exhaust, with cannon muffler w/ 5.5” tip

Heavy duty clutch with 2500lb pressure plate - installed earlier this year at Ross’ Autoclutch

GFB boost controller

Apexi EL boost gauge in Greddy single pillar mount

Pod filter

Bosch Motorsport fuel pump

Cusco brake master cylinder stopper

RWD / 4WD switch

Front strut brace

Car resprayed in Holden Hot House Green, with gold pearl

Trust aftermarket front bar

GTR side skirts

Rear wing removed

Car debadged

Black tint

Lowered 5Zigen aftermarket suspension

17”x8” Advanti Racing Stalker wheels

4 as new Kumho Ecsta 712 tyres; 255/40/17 all round

Alpine MP3 deck

Kicker 6.5” splits in the front

Kenwood 7x10” speakers in the rear

Clarion amp

Alpine subwoofer

Autosalon 2004 trophy winner.

PM or email at :

[email protected]

Or, phone 0402 14 14 38

$19,500 ono

(Plates not included)

Link to comment
https://www.sau.com.au/forums/topic/65375-fs-r32-gts4/
Share on other sites

Donarto : yeah I had the car on the dyno at SST here in Perth and made 242 or 243rwhp. I'll try and find the chart and post it up if you want to see it. Also, getting rid of it because I feel like a change ... going to buy a V8 I think!

Alpha : I'm in the Western Suburbs.

Link to comment
https://www.sau.com.au/forums/topic/65375-fs-r32-gts4/#findComment-1232730
Share on other sites

HAHA... Thats ok man, Ive got a few people interested in it anyway and Im getting excited at the fact that the commodore might be going soon!! Woohoo!!! No more sluging around Perth feeling like in in my late 40s " No offence intended for all those perfectly fine people who are 40 or above.."

Link to comment
https://www.sau.com.au/forums/topic/65375-fs-r32-gts4/#findComment-1232922
Share on other sites

  • 8 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The spray cans were in the "Kiln" room whilst I was preping the parts,  so probably around 2 hours to get them warmed up, the kiln room has 3 small ovens running at 100°c, 3 medium sized ovens running 100°c, and the large one I used running at 80°c, the room itself was about 28°c, I also spent a bit of time taping up the parts in the room as well, and by the time I was done I would assume that the parts were around that 28°c As for power, I expect a couple of Killerwasps up high would be achievable with the current mods, I'm still running the MZR 2.0 intake and throttle body, and there is a slight mismatch with the 2.0 intake (smaller) and 2.5 intake ports (larger) on the head, this intake is matched and specifically designed to fix this issue with the ports mismatch, the throttle body is also a couple of mm larger, OEM is 65mm, the Bosch is 68mm In the end it will look "prettier" than the molded plastic thing that is the OEM MZR 2.0 intake As for the LSD, it's the OEM Torsen which works fine for what I use the car for, plus, basically no maintenance apart from the occasional oil change
    • I was at Tunehouse in Marrickville (great team over there really know their VR's) , and I spotted this Very clean R35.  
    • Mate , I have the same issue right now with the exhaust noise , if you can tell me what your local guy did , I'll talk to my guys and see if they can do the same. Power is good but it just too loud when put it down. 
    • The other trick I've found with wrinkle black is to put the can in hot water for a bit to warm the paint up, and to pre-heat whatever you're painting. It'll be interesting to see if you pick up any power with the intake, following with interest. Got a proper lsd for this?
    • Plazmaman 76mm Pro Series, done. Data to back it up, I posted up somewhere here a few years back
×
×
  • Create New...