Jump to content
SAU Community

Recommended Posts

after going head to head with a wrx with minimal mods on the freeway.

score even (even though i was short shifting)

i new something was wrong... not making enought power

one week later noticed that at part throttle car was hesitant so new there was something wrong

so sent it in to get the injectors flowed.

injector guy flowed them and before cleaning they were flowing 210cc. WTF

now that is ***in dirty

they r supposed to be 440

now the r clean the car goes like a gtr should.

havent taken it for a good run but i think a 55% inprovement in flow should make it hall arse again.

once again i can hapily destry most things on the road

moral get your injectors cleaned it doesnt cost shit

pete

Link to comment
https://www.sau.com.au/forums/topic/6553-get-your-injectors-cleaned/
Share on other sites

200

done a Grey imports at annendale(0419995150) in out with all new seals

not i pulled em out but busted the o- ring when putting em in so got my mechanice to get them cleaned and installed properly.

takes about 30 mins to pull out (dont know what im doing).

you should see how much harder it pulls not its like a new car

i like it

note my car didnt run for 2 months while i was away. i think that is where it really clogged up.

the injector guy said they were in a shocking state

get it done before you do damage to your engine is what i preach now

pete

Just a bit curious if any of you guys exactly how injection shops actually go about cleaninig injectors, what parts do they change, solvents used, etc.

I am thinking of doing it myself as i can obtain an ultrasonic bath for the cleaninig. I am just unsure of the procedure and if the ultrasonic bath cleaning is a good idea, as the high frequencies may actually make more damage that good to the coil....

Anyone know?

If not, can anyone recommend any trustworthy places and pricing?

Taking Injectors out of thr GTR is the easiest thing on this planet besides ****s.

I cost me $12.50 each to clean the injector plus only a small amount for labour to take out.

GTST are a bit harder but not by much.

As Pete Says. Its one of the best things you can do to your car.

That $12.50 includes new seals and all!!!

So when you go to do a cold start in the morning you will have full pressure in the lines and it wont stutter when you start because no fuel leaks into the engine when you dont start it for awhile.

Plus at least next time when you have a problem you can rule out it isnt dirty injectors or old seals.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...