Jump to content
SAU Community

Recommended Posts

New pics towards bottom

Nissan 180sx

1990

5speed manual

CA18DET

Candy Orange

115,000kms

Engine...

Rebuilt Engine - Approx 8.000kms ago

Forged Pistons

Forged Rods

Polished engine bay

3" Exhaust from the turbo back

S15 T28bb turbo

Stainless Steel Exhaust Manifold

Frontmount I/C

Stainless Steel Custom Chrome Piping

Malpasi fuel pressure reg

ARC Blow off valve

Polished Oil Catch Can

Strut brace

M's Pod filter

Body...

Custom Sunburnt Orange Candy Paint

Black roof and bonnet

Wide Body Front Guards

GP Sports Front Bar

Vertex Side Skirts

M Sports Rear Bar

17" Shadow Chrome wheels

Lowered King Springs

Interior - For what its worth...

Greddy Boost guage

Apexi rev/speed meter - Old version

Blitz Turbo Timer

Sony Headunit

Momo Steering wheel

Notes....

Engine Oil Changed every 3,000kms

New Diff Oil

New Gearbox Oil

6months Rego

First and foremost car needs a respray.... The paint is very uneven applied.

Engine is in great condition, with compression test reading 160 exactly over all 4 cylinders.

Car runs perfect and is rather quick due to the mods performed.

Boost is set at 10psi and has not exceeded that figure.

Turbo is 18,000kms old, perfect condition as expected.

Lots of money has been spent to get the car this far, im not going to calculate the expense.

Price $14,500 negotiable

I can be contacted via PM, email [email protected] or phone 0413220070

Pics...

Image%20024.jpg

Image%20002.jpg

Image%20003.jpg

Link to comment
https://www.sau.com.au/forums/topic/66113-180sx-forged-ca18det-mods-pics/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...