Jump to content
SAU Community

A31 Cefiro Body Dimensions

S13Deviat
 Share

Recommended Posts

S13Deviat Grand Master

S13Deviat

Posted
Posted

Hey guys & gals.........have finally tracked down a suiting ceffie and should hopefully be in my hands within a month. (As long as all things go well once it gets here) :wassup:

Now i am trying find out the true width and length of the A31 Cefiro 88'. I have found some sites with listings but they seem a little off. I am trying to measure up if the beast will fit in the garage. If anyone could confirm or inform of the correct dimensions it would be greatly appreciated.

The dimensions i have found are 1486cm-width & 4760cm-length

Firstly the width seems a little 'skinny' and length seems approx correct. I dont have much room to spare in the garage as it is a little one and am looking @ dimensions of approx 4900cm-length and 2500cm-width.

As you can tell not much room to spare so if anyone has a spare 5 min, a tape measure, it would be greatly appreciated. Or alternatively if anyone has official dimesions...that would be awesome to!!!!

Cheers :D

Link to comment
https://www.sau.com.au/forums/topic/66579-a31-cefiro-body-dimensions/
Share on other sites
dangerous_daveo Grand Master

dangerous_daveo

Posted
Posted

It will fit no worrys. Im not going to go out and get a tape measure, but it will fit.

Your just maybe going to have to be a bit careful getting in and out of the car, more so if you have a passenger.

S13Deviat Grand Master

S13Deviat

Posted
  • Author
Posted

AHAHAHA well hey a little persuasion gets you a long way!! :wassup: :rant: I think i may have to move some shelving in it but all should be good. Well all things going well, it will be another Ceffie hitting the North Shore :headspin:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...