Jump to content
SAU Community

Cold Starts


Recommended Posts

The problem you are having is that on colder mornings the computer uses the water temperature of the car to decide how much additional fuel to add to the engine, until the engine/water temperature is normal. I know that with the R33 there is some type of sensor on the plenum chamber that should compensate for the temperature, maybe your's is not working properly.

I have aftermarket management so I can fully adjust the amount of fuel added at cold start. If you don't have programmable managment then I'm not sure what the answer is, speak to a tuner, i.e. Steve at SST.

It's not going to do any harm but it can be annoying having a car that jerks and stalls in the morning.

See'ya:burnout:

Link to comment
https://www.sau.com.au/forums/topic/6738-cold-starts/#findComment-100133
Share on other sites

Guest GR33DyMANGO

i used to experience that problem when i used to own a lancer.

it can easily be solved by running some injector cleaner through the car. run this rich by using the injector cleaner in when theres hardly any fuel left.

another way i fixed the jerkiness of my car when starting it was by using high quality fuel. in this case i used BP Ultimate. maybe you're using cheap fuel? remember to always use high octane fuel. this will ensure your skyline will remain in good condition:)

Link to comment
https://www.sau.com.au/forums/topic/6738-cold-starts/#findComment-100175
Share on other sites

Using it when your fuel is low?

That kinda defeats the purpose doesn't it?

When your on low the bottom of the tank is all gunk, so ur burning some contaminates, i can see by adding the injector cleaner mite of cleaned it , but doing that wouldn't make sense??

Am i wrong??

Donnie

Link to comment
https://www.sau.com.au/forums/topic/6738-cold-starts/#findComment-100246
Share on other sites

My R33 has a VSPEC diff in it, that means it has both the traction control and Active LSD like that found in the VSPEC. These came from the Nissan factory like that, I know of only a couple other people in Aus. with them. The Active LSD is really cool for high speed cornering.

See'ya:burnout:

Link to comment
https://www.sau.com.au/forums/topic/6738-cold-starts/#findComment-100495
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This is how I last did this when I had a master cylinder fail and introduce air. Bleed before first stage, go oh shit through first stage, bleed at end of first stage, go oh shit through second stage, bleed at end of second stage, go oh shit through third stage, bleed at end of third stage, go oh shit through fourth stage, bleed at lunch, go oh shit through fifth stage, bleed at end of fifth stage, go oh shit through sixth stage....you get the idea. It did come good in the end. My Topdon scan tool can bleed the HY51 and V37, but it doesn't have a consult connector and I don't have an R34 to check that on. I think finding a tool in an Australian workshop other than Nissan that can bleed an R34 will be like rocking horse poo. No way will a generic ODB tool do it.
    • Hmm. Perhaps not the same engineers. The OE Nissan engineers did not forsee a future with spacers pushing the tie rod force application further away from the steering arm and creating that torque. The failures are happening since the advent of those things, and some 30 years after they designed the uprights. So latent casting deficiencies, 30+ yrs of wear and tear, + unexpected usage could quite easily = unforeseen failure. Meanwhile, the engineers who are designing the billet CNC or fabricated uprights are also designing, for the same parts makers, the correction tie rod ends. And they are designing and building these with motorsport (or, at the very least, the meth addled antics of drifters) in mind. So I would hope (in fact, I would expect) that their design work included the offset of that steering force. Doesn't mean that it is not totally valid to ask the question of them, before committing $$.
    • The downside of this is when you try to track the car, as soon as you hit ABS you get introduced to a unbled system. I want to avoid this. I do not want to bleed/flush/jack up the car twice just to bleed the f**kin car.
    • But again, the engineers said your cast aluminium would be fine based on the load that would be stretching that section. Same load stretching the bolts in a flex (not the twist), with a much smaller cross sectional area than the original part you've broken. It's why you'd need to be using higher strength bolts, but that's just making up for the strength you lose with less area...
    • I am truly amazed someone on this planet was able to cycle the pump using a scan tool. I've always ghetto cycled them on Nissan 90s shit boxes by slamming the brakes and pulling the handbrake to agitate the rear wheels enough to cause a speed difference
×
×
  • Create New...