Jump to content
SAU Community

Recommended Posts

got some mods done the other day, including a pod located where the stock intercooler resides on a r33 series 1

its noisy as (i think a noname pod)

anyone know if different pods make less/more noise?

not so much that i dont like the noise, id just like less noise if its an option

Link to comment
https://www.sau.com.au/forums/topic/67416-pod-noise/
Share on other sites

pod is already on, stock filter is long gone, so not an option

probably doesnt help that ive lost the inner wheel guards

as the pod noise is right in front of the wheel, which probably throws it around a heap

Link to comment
https://www.sau.com.au/forums/topic/67416-pod-noise/#findComment-1251405
Share on other sites

Your nuts having the pod down there!! If you get water sucked into your intake your 'no name' pod will cost you an RB25DET.

Cheap pods will be made of thin material so the noise you are hearing is the normal intake noise with very little air restriction when its sucking in air.

You can test this by removing the pod and using a stocking to cover the intake and if it sounds the same then you know its just the cheap thin make of the pod you have.

Link to comment
https://www.sau.com.au/forums/topic/67416-pod-noise/#findComment-1251849
Share on other sites

mmm, ive heard others doing similar thing without any dramas

of course ill be careful driving through puddles and what not;

the lowest point of the pod, is about centre of the wheel height, maybe a bit higher;

Link to comment
https://www.sau.com.au/forums/topic/67416-pod-noise/#findComment-1252058
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Has equal chance of cleaning an AFM and f**king an AFM. I think you can work out what happened. When the Hitachi ECU sees the AFM die and goes into the associated limp mode, then it will start and run just fine, because it ignores the AFM and just runs on idle maps that will do what it needs to get it going. But there is no proper load signal, so that's about all it can do. My suggestion? If you don't want to go full aftermaket ECU, then get some R35 GTR AFM cards and some housings to put them in, in the stock location, and Nistune the ECU. Better to do a good upgrade than just replace shitty 40 year old tech with the same 40 year old tech.
    • So my car was recently having trouble starting on initial crank, I would need to feather the gas for it to start up but besides that it would start and run fine. So I clicked the idle air control valve (with throttle body cleaner) and cleaned the MAF sensors (with MAF cleaner). The start up issue was fixed and now the car turns over without the assist of the throttle, but the car is in limp mode and wont rev past 2.5k RPM. From what I understand the IACV would not put the car in limp mode, so I am to believe it is the MAF sensors, but it was running fine before and now I cant get it out of limp mode. I cleaned the MAF made sure the o rings were seated properly. Made sure the cables were plugged in properly, the cables also both read the same voltage. Does anybody know why this is or what could be causing this or how to get it out of limp mode?
    • Ooo I might actually come and bring the kids, however will leave the shit box home and take the daily
    • Thanks. Yeah I realised that there's no way I'd be able to cover the holes with the filler, it would just fall through. Thanks again @GTSBoy!
    • That was the reason I asked. If you were going to be fully bodge spec, then that type of filler is the extreme bodge way to fill a large gap. But seeing as you're going to use glass sheet, I would only use that fibre reinforced filler if there are places that need a "bit more" after you've finished laying in the sheet. Which, ideally, you wouldn't. You might use a blob of it underneath the sheet, if you need to provide some support from under to keep the level of your sheet repair up as high as it needs to be, to minimise the amount of filler you need on top. Even though you're going bodge spec here, using glass instead of metal, the same rules apply wrt not having half inch deep filler on the top of the repair. Thick filler always ends up shitting the bed earlier than thin filler.
×
×
  • Create New...