Jump to content
SAU Community

Recommended Posts

i have rather locked rear end....

I should say if I stand on the brakes it put enough resistance on the diff to get it to move.

Id say its suspension tho... if the wheel is off the ground, the suspension doesnt have the travel.

its going to become handy if i wanna change the oil i guess haha..

but i dont think its the suspension the main cause.

i have cage, body's been re-enforced with many more welds, one of them do-luck bars,

its like a sea saw when you park it in the right spot..

i have full race roll cage in mine (no rear seats, sun visors etc etc). Chassis don't flex that much. (well not on our cars anyway!)

I know what Daveo is talking about my ceffie gets beached, JIC suspension and a 2way, I jack the car up from behind the front wheel and 3 wheels come off the ground!

I love my suspension on smooth roads but... our roads generally suck so its annoying at times!

It's actually a case of your chassis being VERY stiff and NOT deflecting. This is a *good* thing (I'll get back to this later).

The fact that your chassis is welded and has a bolt in roll cage means that the torsional rigidity of your car is significantly improved. Thus, it takes much more twisting motion to flex the body. An illustration of this is, when you jack a car up at one corner, the windows and doors tend not to fit quite right. However, when, if you've got your car jacked up at one corner, the doors *may* open and close properly. ie. stiff chassis = good for maintaining suspension geometry and thus handling.

The *good* thing that the wheel is in the air now... It is good because it illustrates that your chassis has been reinforced well. However, it also illustrates that your shockers, at full extension, are significantly shorter than the factory stuff (same as my car). What this means is that, the shock length is shorter and thus the 'droop' that the wheel had drop to is shorter than the original factory suspension. An example of this is when you see a 4WD with very long travel shocks / springs climbing rocks that can articulate the left front wheel entirely within a guard and the right rear wheel at full extension that leaves a wheel to guard clearance of 50-100cms (see below pic)

Escursione%20sui%20Nebrodi%20Domenica%2021%20Sett%202003%20in%20compagnia%20dell

So all it means is that you'll lift wheels when getting into / out of driveways etc, you'll notice that Porsche GT3 RS's do it too...

So, if you've bothered to read this far, this is a good thing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...