Jump to content
SAU Community

Recommended Posts

i have rather locked rear end....

I should say if I stand on the brakes it put enough resistance on the diff to get it to move.

Id say its suspension tho... if the wheel is off the ground, the suspension doesnt have the travel.

its going to become handy if i wanna change the oil i guess haha..

but i dont think its the suspension the main cause.

i have cage, body's been re-enforced with many more welds, one of them do-luck bars,

its like a sea saw when you park it in the right spot..

i have full race roll cage in mine (no rear seats, sun visors etc etc). Chassis don't flex that much. (well not on our cars anyway!)

I know what Daveo is talking about my ceffie gets beached, JIC suspension and a 2way, I jack the car up from behind the front wheel and 3 wheels come off the ground!

I love my suspension on smooth roads but... our roads generally suck so its annoying at times!

It's actually a case of your chassis being VERY stiff and NOT deflecting. This is a *good* thing (I'll get back to this later).

The fact that your chassis is welded and has a bolt in roll cage means that the torsional rigidity of your car is significantly improved. Thus, it takes much more twisting motion to flex the body. An illustration of this is, when you jack a car up at one corner, the windows and doors tend not to fit quite right. However, when, if you've got your car jacked up at one corner, the doors *may* open and close properly. ie. stiff chassis = good for maintaining suspension geometry and thus handling.

The *good* thing that the wheel is in the air now... It is good because it illustrates that your chassis has been reinforced well. However, it also illustrates that your shockers, at full extension, are significantly shorter than the factory stuff (same as my car). What this means is that, the shock length is shorter and thus the 'droop' that the wheel had drop to is shorter than the original factory suspension. An example of this is when you see a 4WD with very long travel shocks / springs climbing rocks that can articulate the left front wheel entirely within a guard and the right rear wheel at full extension that leaves a wheel to guard clearance of 50-100cms (see below pic)

Escursione%20sui%20Nebrodi%20Domenica%2021%20Sett%202003%20in%20compagnia%20dell

So all it means is that you'll lift wheels when getting into / out of driveways etc, you'll notice that Porsche GT3 RS's do it too...

So, if you've bothered to read this far, this is a good thing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...