Jump to content
SAU Community

Recommended Posts

Alternatively, if you would like to use a smaller filter to reduce the time it takes build oil pressure at cold start.....and because it makes it easier to service. You can use the ryco Z386. They fit on perfectly and give a little more room when changing them.

They flow plenty, they are used on engines such as the 2JZGTE supra engine.

Link to comment
https://www.sau.com.au/forums/topic/70377-what-oil-filter/#findComment-1299971
Share on other sites

Hey replicate,

All RB Series Engines use the same oil filter, following are part Numbers:

Genuine: 15208-H8911AU

Ryco: Z145A

Hope this is some help,

Andrew

RB25DET NEO's use a different one, the same as GTiR's i believe.

Edit: Here it is, NEO's use Z442

Link to comment
https://www.sau.com.au/forums/topic/70377-what-oil-filter/#findComment-1300657
Share on other sites

Alternatively, if you would like to use a smaller filter to reduce the time it takes build oil pressure at cold start.....and because it makes it easier to service. You can use the ryco Z386. They fit on perfectly and give a little more room when changing them.

They flow plenty, they are used on engines such as the 2JZGTE supra engine.

Ryco website lists Z418 as the applicable filter for Supras...

But, this site lists their HD-05 product as a repalcement for all of these Rycos: Z82,Z125,Z145A,Z158,Z386,Z418, so they'd all fit, whether they're all up to the task is another matter...

Link to comment
https://www.sau.com.au/forums/topic/70377-what-oil-filter/#findComment-1300691
Share on other sites

They are certainly up to the task........especially if you service your car at the appropriate intervals...........large filters are only good if youplan to service your car after very long periods (bigger filter will hold more crud than a small one)

BUT the smaller filter will help your engine gain oil pressure quicker on cold start.

Link to comment
https://www.sau.com.au/forums/topic/70377-what-oil-filter/#findComment-1301963
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...