Jump to content
SAU Community

what oil do u guyz and galz use on ur skylines ?

ZOR

By ZOR,
in General Maintenance

 Share

Recommended Posts

«Cyph3r» Experienced

«Cyph3r»

Posted
Posted

Currently using REPSOL COMPETIZIONE ELITE but will be switching to MOTUL V300 CHRONO from now on.

Someone i know blew there oil filter out and ran with no oil from the gabba to tingalpa and was up it quite a bit a lot of the way as didn't realize had no oil left in motor.

The workshop pulled the motor down and said why did you want us to look at it and didn't believe he had run without oil as was perfect. Not a thing wrong !!!

He was using MOTUL V300 CHRONO when this happened.

Is enough to convince me that this oil is the stuff to get.

Jamie

superspit Mentor

superspit

Posted
Posted

this 'gal' uses (and recommends) Target Premium Brand...costs $7.99 for 8 litres...........stuff paying $25-$30 like the rest of you guys (and gals)!!!

By the way, the grocery guy at Target rekons 20-50w is pretty good!

mmmm.................

Seriously.........Like everything in life you get what you pay for....just get the first number right!

krush Collaborator

krush

Posted
Posted

i done much searching on this for my first oil change in the skyline, and the impression i got was Motul 4100 10w-40 was where its at.

so.. i went out and bought like four litres for $50 from autobarn.. you guys had better be right :)

(no no.. i wasnt threatening.. honest!)

:)

shaun.

superspit Mentor

superspit

Posted
Posted
i done much searching on this for my first oil change in the skyline, and the impression i got was Motul 4100 10w-40 was where its at.  

so.. i went out and bought like four litres for $50 from autobarn.. you guys had better be right ;)

(no no.. i wasnt threatening.. honest!)  

:)

shaun.

Shaun,

your baby will be just fine!!

I love this stuff, and so do a lot of other people.

Never actually heard a bad word about it!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nash47
      Cas issue

      By nash47 · Posted

      Did and sync timing with light 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...