Jump to content
SAU Community

Recommended Posts

Hi All

I just fitted a ARC FMIC Kit yesterday and the power feels more smoother but no as great...the kit was second hand, do you think that there could be a hole in the cooler or hosing, or do you think its just my imagination...any help would be great...and yes ive double checked the clamps and they are super tight....cheers

Link to comment
https://www.sau.com.au/forums/topic/72288-intercooler-question/
Share on other sites

Hi All

I just fitted a ARC FMIC Kit yesterday and the power feels more smoother but no as great...the kit was second hand, do you think that there could be a hole in the cooler or hosing, or do you think its just my imagination...any help would be great...and yes ive double checked the clamps and they are super tight....cheers

I've had a small hole in my cooler before. You definitely know when you have a hole in that you can definitely hear it even off boost.

not vacumm but boost seems a little low (still at stock) but feels not a hard to kick in...i didnt know if this happened when fitting a fmic or not

Whats your vacuum at idle? should be around -500 ( reading of the PFC hand controller on mine)

Umm I am definitely no expert... but it just sounds like the bit of extra lag you get from fitting a FMIC and all that piping compared to the stockie???? Normal I thought - hence why u normally combine the FMIC with mods like a full turbo back 3" exhaust and a bit of extra boost etc to balance out the lag... the FMIC istself doesnt do much for performance - but creates a cooler environment to allow you to fit more mods and up the boost with less risk

Personally I wouldnt do a FMIC if you werent modding up - but then again thats just base on other reading in here - so i could have it completely wrong :rolleyes:

i will check the vacumm next time i start up...brazen cheers , but i have a 3inch system

Yeah - but whatever mods you have - at the point you install a FMIC you will get an increase in lag over what u had before the FMIC... did u have a FMIC before and just swapped to a Blitz system - or go from stock sidemount to FMIC?

Yup - thats all it is - you've introduced a bit more lag with the extra length of intercooler pipe - so it'll feel a bit more sluggish - although your peak performance probably hasnt dropped - just changed your curve.

The FMIC just now will allow you to do a few more adventurous things to up your power and push it power back down the curve a bit - whereas pushing a bit more with the stock cooler would start getting risky further down the track... talk to your tuner... but the FMIC and maybe a couple of extra bits and pieces should now let you up your boost if you so wish or do more hardware mods. It wont take much now to get that lag out of the way and make the car FEEL fast again :(

if the cars stalling, from my experience, the fmic should have nothing to do with this saga..

perhaps, check with your tuner about these few things..

- b.o.v could be leaking,

- fuel pump maybe earthing

- if its a series 1, rb25det, check you coil packs & the ignitor pack above the #6 coil pack

- crank angle sensor maybe ****ed, & might need replacing

* my car did this, i though the b.o.v maybe leaking, but that wouldnt cause your stall

- my cars crank angle sensor was not sending the right signal, & the ignitor pack was ****ed as well, ive replaced both c.a.s & the ignitor pack ( as we speak its in shop) & the mech said thats my problem, maybe yours too...these are just a thought...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
×
×
  • Create New...