Jump to content
SAU Community

Recommended Posts

Hi there Various R33 Parts for sale...

Plese don't delete MODERATORS, PM with bank details so I can make trader deposit as requested via email without any response yet.

Mark

Just testing the waters to see which parts are most popular. I have These parts for R32 as well and MAY have them for R34 but please enquire via PM.

Apexi Power FC with H/C - $850 New

Apexi SAFC II - $380 New

S2 Genuine Floor Mats - $100 S/H

Blitz 700cc Injectors - $600 NEW

R33 GTST standard airbox - $100 S/H

R33 Complete front doors - $300ea S/H

Blitz dual drive blow off valve - $250 S/H

HKS SSQ Blow of valve - $250 NEW

Mspec R33 Front Bar in black - $100 S/H

Front Strut Bars - $80 S/H

Greddy Profec A EBC - $300 NEW

1x Xenon Headlight set for R34 GT-T - $900 S/H

Just a note to all buyers outside of WA. I will only accept payment via COD(you pay for the cost of it), direct deposit or Internet Banking Transfer. To All In WA, if distance is not a problem. I Prefer Pickup. Shipping of parts will be with Australia post unless its an item which australia post does not deliver due to size. Shipping costs are all part of the buyer's responsibility.

Mark

Link to comment
https://www.sau.com.au/forums/topic/72606-various-parts-for-sale-r33/
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...