Jump to content
SAU Community

100K service and nice power increase! ;)


flagger
 Share

Recommended Posts

well i put my car into hardcore racing at slacks creek today for my 100K service. got the usual stuff done, timing belt, water pump, diff oil, gearbox oil, seals, bearings, etc

anyway, things that were stuffed:

- water pump: all the teeth were chopped off. somehow it was still pumping water, but i doubt it would have for much longer. the mechanic said it was the worst water pump he had ever seen

- coil packs: i was getting misfires after coming off mid-high boost. turns out both packs had cracks, and 3 electrodes were damaged to all buggery. only 2 were in a "ok" state

so after that was all fixed/replaced a dyno run/tune was done (dyno run done before service too)

dyno-100K%20service-5-5-05.jpg

very nice increase. its a helluva lot smoother now, the gearbox is way more nicer to shift now and now i know the car is mechanically sound again. it wasnt cheap though, the coils bloody cost a lot (2nd hand as well).

so the moral of the story is: if your due for a major milestone service, go and do it. u might not know what parts may be at their limit.

Link to comment
Share on other sites

wow.. they slapped a bit of a markup on the timing belt. They are usually around the 90-100 mark direct from nissan. :cheers:

Not to mention those second hand coil packs. I picked one up from the wreckers on Thursday for $77, would be interesting to know what you got charged for them...

Link to comment
Share on other sites

$77 for second hand jobs.. Shiet.. :cheers:

Thats $462 for a complete set.

Spend another hundred or so and you can have a set of Spitfire coils imported from Nengun or Greenline.

Link to comment
Share on other sites

$77 for second hand jobs.. Shiet.. :cheers:

 

Thats $462 for a complete set.

 

Spend another hundred or so and you can have a set of Spitfire coils imported from Nengun or Greenline.

But I only needed the 1. Maybe if several had shit themselves together I would had paid the extra for Splitfires, but in this case $77 was much better than $600+...

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Agreed with the rest. Also at least based on my own research, there are no readily available stock or close-to-stock RB20Neo maps that you could download and use as a base were you to buy a complete standalone ECU, and the regular 20DET maps don't really work well so you'd need to take it to a tuner if you have no experience. I installed an AEM V2 on my 20Neo+T and had lots of headaches until I got it to run and idle properly but I've yet to remap it fully. You have to start building up your timing and fuel maps entirely from the ground up; even the ones for a 25 didn't work at all.
    • Got some decent progress after work yesterday and also today. Got the ECU all wired and passenger side interior all back together. Kept the wiring up nice and high to avoid people standing on it. Got the surge tank relays rewired and tidied up the pump wiring and cut a hole to bring the cables through.  I found a spare USB cable I had lying around so I decided to cut it up and see if I could use it for my CAN 1 bus. Turned out one of the pins I needed was to the shield of the cable so i cut it up and desoldered it and resoldered to the correct pins.  Had the issue with the powersteering hose hitting the A/C compressor and fan shroud. I pulled the bracket off and modified it to remove the front mounting point which now clears it all. Will keep an eye on it to see if theres any signs of fouling once it's up and running.
    • That's some good input mate. Nice.
    • So today I went well outside my comfort zone (again) to replace my valve cover gasket.  I have had a big leak over the exhaust leading to a lot of smoke and smell every time I drove it. The leak was in the rear driver's corner.  The job wasn't hard as such, just a bit finicky and time consuming.  The old gasket was rock hard and broken right where the leak was.  The leaky corner had so much sitting oil in it.  The good news to my amateur eyes was no buildup or sludge under the cover. It all looked fairly nice in there.   I haven't started it yet. I ran out of light and body when putting the coils and injector loom back in. Probs only 30min left for the morning.  I was so nervous putting the cover back on, I must have lifted it 5 times to make sure the gasket was still seated properly. God it's going to be nice to be leak free and not make other traffic light queuers think my car is about to explode.
    • Gave the Mazda it's first wash, it will need some clay, a light compound, and polish polish to remove a few swirl marks, but that will be a job for when I have a full day to get my DA polisher action on
×
×
  • Create New...