Jump to content
SAU Community

Recommended Posts

Is launceston closer?

yeah give us a hint where you live mate as there are pleny of people state wide that can help you out and maybe cut down your travel time as well :)

Cheers B

  • Replies 121
  • Created
  • Last Reply

Top Posters In This Topic

Is launceston closer?

Yeah Launceston is closer by about, give or take an hour.

last time i drove too hobart took 3 and a hlaf hours

only takes close to 2 hours to get to launnie.

I usually travel to launnie every days off so you know where all the speed cameras are as well :)

Oh i live in Rosebery West coast :)

Edited by drumstick29

Awesome dude thanks,

Im saving money while i dont have a licence lol...

so i wanna do a major upgrade upgrade turbo and all that stuff should havea fair bit after i get it back. close to 25K but not sure what to do too the car part from turbo upgrade and bigger injectors and fuel pump i wishi was a mechanic sometimes :P

Well as an example Phat R33 and i have both just rebuilt and are putting big turbo's on RB25's and both went different ways about it, but both got our work done at S&D Bell Auto...

Im not giving figures of whats been spent by either of us but the questions to ask yourself is, what do you want to do with the car... IE; street driven, drag, track, drift, combo of a few etc

How much power do you want to make, and when would you prefer it to be made?

these sort of questions will determine what you do and do not need to do to get power out of the engine...

I could waffle on all day about this, but i will wait till you can answer more questions (and im sure others would like to have a say too)

maybe start a new thread about this?

My personal favs' in Hobart are;

1. white 70's cortina with HKS stenciled on the side

2. purple lancer with more primer than body kit

3. several VL commodores with NISMO Stickers.

  • 2 weeks later...
  • 4 weeks later...
Anyone in Launceston seen the loser who has just appeared in the white Camira?  Every time I've seen him he's been blasting around and driving like a f*&^wit.  Checkerplate where the back number plate goes, and it looks like he's either put a big radiator with flashy pipes or a FMIC on the front.  Include the set of alloys and you've got a full on performance car!

What about just starting with a decent car?

That guy is a fu#k, the thing is a "cold air intake" to add to the list of gayness it has LED's that flash in ghey patterns..... this is just an example of how much of a dick he is. .........sr20det, from a GTiR USING THE 4WD BOX........in a camira.........

Apologies if this one has had a mention, ut my personal fave - in hobart, most often spied in new town, a red lada coupe. This thing has the hand made, oversize drift wing, hand cut stickers, a stick on bonned scoop, and an exhaust that would wake the dead...

I was talking to a gent at autobarn, and apparently they will sell about four stick on bonnet scoops a week, and most of them will stick them on in the car park!

I got stuck talking to a girl (herself complete with fox t-shirt and 7 facial piercings) she said I should grab some blue neons, paint the lower half of my black 32 silver, throw on some stickers and "it will look really good, trust me" aaaaaagh deliver me!

here's another.  Blue auto pulsar, early 90s model with massive Nismo sticker.

I think that one is from down my way in St Helens. sounds a bit like the one i see all the time.

Apologies if this one has had a mention, ut my personal fave - in hobart, most often spied in new town, a red lada coupe. This thing has the hand made, oversize drift wing, hand cut stickers, a stick on bonned scoop, and an exhaust that would wake the dead...

Yeah seen that one around. Brillant ain't it! It's amazing how many stickers you can make with white electrical tape. Got him at the lights a few weeks ago and he decided that key bangers were the order of the day. From Davey st in town to the Mornington roundabout! I counted at least 40 of them!

Edited by MadR32GTS-4

Ok here is one for you, a Hyundai S coupe (im sure thats what it is), with bodykit, gt wing, chrome rims and stuff... with ralliart and trust stickers on it.

The best bit, he calls it a tiburon!!!!!

Ok here is one for you, a Hyundai S coupe (im sure thats what it is), with bodykit, gt wing, chrome rims and stuff... with ralliart and trust stickers on it.

The best bit, he calls it a tiburon!!!!!

Is that one blue? and has holden supercharged badges on it?

  • 1 year later...
let's get this one going again. There must be some new classics, most of the others would have carked it by now! Especially the white camira (I hope!).

DAMN DUDE long time no post, how you been, still got the 32's???

DAMN DUDE long time no post, how you been, still got the 32's???

No more 32s, all sold. The market got flooded with rubbish when the 15 year rule went out the window, dragging down the value of decent cars.

Although the amount of Skylines that have been pranged in tassie there might be a market just in supplying replacements :ermm:

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...