Jump to content
SAU Community

Recommended Posts

Hi people out there,

I was just wondering if anyone knows how hot their turbo's get. I know that this is a "how long is a peice of string" question but I am interested to know if anyone has gone for a drive or race perhaps and whacked a laser thermometer on their turbo just to see how hot it gets. Perhaps someone has read this info some where. If you have, then please tell...

Your tubo size and engine will make a difference in heat as smaller turbos run hotter, etc. Obviously, there would be an operating range depending on how hard you drive, etc. From what I understand the operating temp could be anywhere from 100 deg c to 1000 deg c! Anyone know?

Chriso

Link to comment
https://www.sau.com.au/forums/topic/73627-how-hot-is-your-turbo-do-you-know/
Share on other sites

lol are you having fun posting this on every single forum, saw it on boostcruising ust before, now here :P

Oops... Busted. :Oops:

:)

Yeah, bit of a forum hussy.

I had a tiny leak at my dump flange and needed to know how hot it get so I can get the right stuff. Looks like I won't need it anymore anyway as I found some loose screws... Still interesting to know though...

wow, you must be fast to jump out, pop the bonnet and look.

i've seen mine red but only on a dyno

i find it stays red for at least around 30 seconds and glows for a minute or so..

and yes i am usually quick, and when i have seen it i have been on a road in the middle of nowhere so no cars and is safe stop anywhere whenever :rofl:

Could be you're right. Damn hot anyway.

Means your trying hard enough :cheers:

btw a bit off topic but i wanted to ask you,

after u fitted the hicas lock bar, was there a difference in the weight of steering at any speed??

i ask this because im quite sure the steering weight varies depending on speed, and figure it might get stuffed up by locking the hicas..

Take a look in the tutorial , but the quick answer is yes it can get hard at low speed (40) due to the system being electrically variably loaded, according to speed. This is common but dissapears with extra caster.

I've had glowing turbo on stock r32 after hard mountain work.. I think its just a combination of having no dump pipe to dissipate the heat better, and the fact that the R32 turbo is pretty small. Could also be related to clogged water lines, but need to investigate this further.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...