Jump to content
SAU Community

FS: 1996 r33 ser 2 250rwkw(MSPEC2)

boosted30
 Share

Recommended Posts

boosted30 Apprentice

boosted30

Posted
Posted

I know ive only had it for 3 months but im looking for an upgrade.

so im willing to trade plus cash adjustment.

I purchased the car of (Heathgtst) on these forums and i have to say i was more than happy with the way he looked after this car.

since i bought it i got the whole front resprayed due to alot of stone chips on the bonnet and a dint in the drivers side gaurd.

Exterior

- dark grey with purple pearl

- trial front bar

- trial side skirts

- nismo clear indicators

- 18x9 drift r wheels with dunlop sp9000 tyres

Intirior

- m's shift knob

- gtr floor mats

Brakes

- slotted dba rotors front/rear

- rb74 racebrakes pads front/rear

Suspension

- bilstien shock absorbers

- pedders lowerd springs (%100 street legal)

- whiteline adjustable swaybars

- whiteline camber kit front

- whiteline camber kit rear x2

- whiteline castor kit front

- whiteline subframe align/lock (pineapples)

Electronics

- Apexi power fc computer

- apexi hand controller

- warlock alarm and 2 point immobilizer

Transmission

- standard 5 speed (always serviced with fully synthetic oil)

- exeedy 5 puck button clutch

Engine

- hks air filter

- custom 3" cat back exhaust

- race pace 3" hi-flow cat

- just jap 3" front pipe

- hks gt2535 turbo

- hks front mount intercooler 600x300x75

- hks 14psi actuator

- gtr fuel pump

- 247 rwkw on racepace dyno

car has 75.000kms on it and the timing belt and water pump were changed at 45,000kms

i have been pulled over numerous times before and they have tried to canary me but have failed.

this car is in prestine condition and one of the best r33's i have seen. It is %100 p plate legal as the tare wheight on the rego has been bumped up to pass the power to weight ratio

i recently got an epa off with the turbo and computer still on the car(the only thing i did was put a small muffler and stock airbox on.

the intirior does not have a mark on it, and it handles and brakes like a dream.

when the car is purchased i will have it re dyno tuned at my own exspense as i want the new owner to get it running perfect.

Only reason im selling her is to upgrade to an r33 gtr

Price $24,000 firm

or trade r33 gtr + cash

Link to comment
https://www.sau.com.au/forums/topic/74166-fs-1996-r33-ser-2-250rwkwmspec2/
Share on other sites
DentonR33 Rising Star

DentonR33

Posted
Posted

Make sure Ben from RacePace does the Retune mate.. pm me if u dont have his email, he has tuned it the whole way along the mod train and had to spent 2 hours fixing someone elses "tune" when it was taken somewhere else! Good luck with the sale.. id buy it if i wasnt in the same boat as u & wanted a GTR :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...