Jump to content
SAU Community

Recommended Posts

So....with a FMIC ill only be looking at a difference of 12P.S.I as opposed to 10P.S.I....cause if im correct a standard turbo cant be boosted more than 12p.s.i safely regardless? Is there a noticable difference in power i.e on dyno run? or is it really not worth the cost if im leaving my turbo standard??

Was that 20KW gain running a stock turbo at 13P.S.I?? And does anyone know if the amount of boost you can run safely depends on the model of the car? eg series 1 vs series 2 r33?

It depends on what car it is, what mods it has (if it isn't stock) and the over all condition that the car/engine/turbo is in. Every car is different, there are no 2 the same. A mate has the exact same car as his brother, one is a 89 gts-t and the other a 90 gts-t, now we are talking 3 months between build dates of them.

They are exactly the same, stock as a rock bar a aftermarket pod, and a end can. Both are stock internals and running gear yet one has 42 rwkw more when put on the dyno.

Why, who know's it could me a number of reasons, the tubro life and engine condtion, stock intercooler, the point is that no two cars are the same, therefor you can't base them as the same.

Sure you can use it as a guide line and go from there but what works for one doesn't mean its going to work for the other :cheers:

Could be to do with the R33 ECU being very prone to dropping timing when intake temps get up. Seems like the R32 doesn't mind so much?

I just bled up my boost to 13psi after fitting my front mount, but I can barely feel any noticeable difference as everything else is stock bar a k&n panel filter. It just drops most of the boost anyhow back to 10psi. Needs exhaust, needs better airflow to the filter...blah.

In other words, raising the boost by itself is pretty pointless.

Yer good point, the Rb25 being 9:1 comp would be closer to detonation, high intake temps probably tip it over the edge quicker.

barely any difference with 13psi... lol That stock exhaust must kill the turbo's efficiency, going from 10.9psi (stock boost with 3" exhaust) to 12.5psi I noticed a definite difference.

On stock 10.9psi feels N/A.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
    • On the bright side, the weather will turn much nicer for working outside shortly....sounds like you might need to start on a neighbour's garden next
    • Ok so i will NEED to have this sensor anyway even with Nistune (or standalone ECU) https://justjap.com/products/genuine-nissan-boost-pressure-sensor-evap-control-system-fits-nissan-r34-skyline-c34-nm35-stagea-pnt30-x-trail-rb25det-vq25det-sr20vet?currency=AUD&srsltid=AfmBOoqfxX48bW9bEwH62orcNhtBfp7ekAL0C9Ca89ySFGUiBzXfXeze Is this the correct one? And this is only thing i need? No other "things" connected to the sensor or something? I do have the wiring.
×
×
  • Create New...