Jump to content
SAU Community

Recommended Posts

Selling parts off my white car, turbo was going to be put on for Drag Combat but didn't arrive in time.

Greddy TD06-25GSH10cm turbo, ceramic coated exhaust manifold for RB20/25, Trust type R wastegate. Turbo is brand new, never been installed. Gimps sent me a 16cm rear housing with it, have now got the proper 10cm rear and getting it ceramic coated this week. $3500 firm for the lot, will seperate $2000 for turbo, $1300 for manifold, $600 for wastegate. Will make 330rwkw+

RB25 camshafts: Reground based off some HKS 256in/264ex cams we had, have been in my motor for the last year. Done about 1200k's, good condition $600

Greddy RB25 plenum and Q45 throttle body: Same as cams, been on my car already. Perfect condition, sell together for $1100 or plenum $900 throttle body $300.

550cc injectors: RB26, low impedance. Installed on the RB25 with the use of an RB26 fuel rail and resistor pack. $550

Apexi adjustable fuel reg suit RB26: Installed on motor, taken off after 2 hours of running as it was not needed. Bolts on to std rail. $150.

RB25 motor: long motor without the cams, intake + exhaust sides. Had 160psi even on all cylinders when we checked it 500k's ago. Don't know if there is even a market for these motors but selling the whole lot and might as well include it. Makes a great anchor or perfect to upgrade your Gemini.

They are not standard GTR injectors, but are suited to an RB26. Top feed, low impedance. I think they are Apexi ones, but they are all made by Denso so no difference.

  • 2 weeks later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...